E******* OMT in WINDOWS 7

[ghanim44]

HI guys
I install OMT R43 in windows 7, when I try to connect to the RBS it gives me an error
" Overlapped I/O operation is in progress"

Please help me !!!!!!!!!!

[abhye_x]

Never try OMT R43 in windows seven.. what about the latest OMT P44? have you try!!

Best regard

[ghanim44]

I tryed P44 and P45 but the same Erorr is shown

any othe ideas???????????

help me please !!!!!!!!!!!!!!!!!!!!!!!!

[Abuelooorl]

Hi.

Follow this steps:

1. Use a VMware Virtual Machine with Windows XP SP2 x86 installed on it.
I suppose you're using a relatively new laptop which have enough power to run that.
2. Configure an USB-TO-RS232 adapter as COM1/2 using the adaptor's vendor original drivers.
I use a Belkin adapter. If this is your case use the Prolific drivers. Install them from whithin your host and guest machines.
3. Install OMT in the VM and connect to the RBS.

Best regards.

[abhye_x]

what about if run the program as administrator?
i mean when you install the program first time instal with the administrator rights.
hope it use

Regard

[ghanim44]

Hi.

Follow this steps:

1. Use a VMware Virtual Machine with Windows XP SP2 x86 installed on it.
I suppose you're using a relatively new laptop which have enough power to run that.
2. Configure an USB-TO-RS232 adapter as COM1/2 using the adaptor's vendor original drivers.
I use a Belkin adapter. If this is your case use the Prolific drivers. Install them from whithin your host and guest machines.
3. Install OMT in the VM and connect to the RBS.

Best regards.

Than you for your replay
I install XP mode with VMlite then I install OMT in it, it works fine with RBS 2206,2207,2216 and 2216 V2, BUT it dosen't work with the new RBS 6000

I hope there is a solution to make it work in Windows 7

[ghanim44]

what about if run the program as administrator?
i mean when you install the program first time instal with the administrator rights.
hope it use

Regard

Thank you
I will try it tomorrow, I hope it will work

[ghanim44]

Any ideas ?????????????!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[chammy]

Hello,

Do you have E*******'s RPM 919 732 cable or did you make the connection cable yourself?
Also there has been reports that certain usb-rs232 adapters and pcmcia cards don't fully comply with the rs232
standard as the pin voltage is not correct. this affects only connections with DUG, not DUL nor DUW.

regards,
chammy

[ghanim44]

Hello,

Do you have E*******'s RPM 919 732 cable or did you make the connection cable yourself?
Also there has been reports that certain usb-rs232 adapters and pcmcia cards don't fully comply with the rs232
standard as the pin voltage is not correct. this affects only connections with DUG, not DUL nor DUW.

regards,
chammy

I made the connection by my self, yes you are right in XP mode the connection effects only the connection with DUG, BUT in windows 7 it gives me the same error.
what if I get the E*******'s RPM 919 732 cable is it will work with windows7 or only in XP mode?????

help me please!!!!!!!!!!!!!!!!!!!!

[handrinha]

try to use a usb to serial converter that is made in china and it will work...guaranteed 100%....the prolific will not work in windows 7 as i have encountered myself the same error I/O over lapping. I used OMT 45

[hooby]

Than you for your replay
I install XP mode with VMlite then I install OMT in it, it works fine with RBS 2206,2207,2216 and 2216 V2, BUT it dosen't work with the new RBS 6000

I hope there is a solution to make it work in Windows 7

i am using the same configuration and it works for both 2000 and 6000 series without any problems. check your settings or something like that.

[boza]

Just for mention.
XP isn't necessary.
P45E and P48M works on W7 x64.
Must check your PC.

[boza]

Just for mention.<br>XP isn't necessary.<br>P45E and P48M works on W7 x64.<br>Must check your PC.

[mouroalgarvio]

I have windows7 with virtual machine xp , omt only works in this mode, and there are some usb -serial that does not work well with the rbs6000.

[boza]

I use relative old usb to serial (Chinese) one, we call it black converter cause its colour.
I leave W7 to find and install driver don’t used manufacturer, … and its work.
In MW field only Siemens Local Craft (Sral, SRA, Flexy) and NEC PNMTj only for Pasolink NEO (reason no NEC USB driver for x64 but works on W7 for old Pasolink V4) don’t work on W7 x64. Just for that I use virtual machine with XP.
For example E******* MINI-LINK Craft 2.17.1 (2.15.2 , …) works ok but stay on IE8 (IE9 makes problem), Huawei Web LCT you can copy installed version from some XP machine and use it on yours W7, etc, …

[VAGOS1]

I have the same problem i was running OMT 48M in W7 without any problem (WITH RBS 6000) , but one day start to have this message " Overlapped I/O operation is in progress".
Now i run OMT 48M WITH VM & WXP and everything is ok .

[striker]

I have the same problem i was running OMT 48M in W7 without any problem (WITH RBS 6000) , but one day start to have this message " Overlapped I/O operation is in progress".
Now i run OMT 48M WITH VM & WXP and everything is ok .




Can somebody share the latest omt?

[bionel]

I have the same problem, I connect to hyperterminal but when I connect to the OMT does not work.

[mouroalgarvio]

I am using windows 7 ultimate with virtual windows xp mode , it works ( OMT45M). USB serial Aten drivers.

[spaceo]

may be you system has some problems.

[maddy_cooljack]

HI guys
I install OMT R43 in windows 7, when I try to connect to the RBS it gives me an error
" Overlapped I/O operation is in progress"

Please help me !!!!!!!!!!

We are also using windows 7 with OMT 45 & 48.
No issue found.
Please check cofiguration.

[edmar_tubil]

We are also using windows 7 with OMT 45 & 48.
No issue found.
Please check cofiguration.

Hi,
Coud you share that omt 48 you have. I was trying to look for that version in this forum but links are not working anymore.
Many thanks.

BR///
Edmar

[maddy_cooljack]

i will be sharing link by tomorrow.

[djenah]

Still no workaround?

[Abuelooorl]

Hi.

The supposed workaround is using an USB/RS232 adapter with a non-Prolific chipset.

It should work fine with any version of W7 (x86/x64) but I haven't tested it yet.

Can someone please confirm this point?

BR

[djenah]

The supposed workaround is using an USB/RS232 adapter with a non-Prolific chipset.
R

Will try this next week and leave a confirmed or not.

[mouroalgarvio]

Here it is OMT48S , it will work on windows 7 .
http://www.mediafire.com/?dk7imsk90t8h22e

Please add some rep.