I think it's used by DMR machines, I also have this software but his UI is corrupted, check your PMs!
Type: Posts; User: BB101; Keyword(s):
I think it's used by DMR machines, I also have this software but his UI is corrupted, check your PMs!
Can I upgrade while keeping the data, e.g. by importing the RMC into a higher version of the template?
Thanks for that. GaborYes perhaps upgrading the radio might be the best option, but I don't have the correct way to do it, I can't find a description of upgrading the firmware in the RM1.81 pdf, I...
I have a Sepura SHR3800, and when I read his info it says mainCodeSoftwareVersion>163900502935.He should be version V8.0-001, yes I think I need this V8.0-001.rmp file, if anyone can provide him I...
I don't know if there is a correspondence between firmware and language. I am using RM1.81, which comes with Asian languages in the software. If there are relevant documents on how to properly...
What is not needed is that the machine is currently in a state where it cannot start up and perform operations, and the screen displays "Engineering mode" as shown in the picture. I connect RM...
I have an SRP2000, but I don't have the corresponding firmware package. Is there any way I can write data. I tried to write a higher version of the template, but the machine stopped turning on. The...
Thank you. After multiple attempts last week, I successfully connected using the FTDI232 chip with only three wires: RXD, TXD, and GND
Here is the basic service manual, which includes pin definitions
https://mega.nz/file/QndQQIDA#5FJNECWE2yirHqUeDWbRyeunGpgFb0Rn9yxpNGcmbx0
Does anyone know the definition of the NOKIA TMR880 programming cable or the definition of the front panel interface.
I found the relevant documents, but they don't seem to be detailed and don't...
I saw him on a Russian website, I don't have it, I only have RM2.8.40.1
There seems to be no solution yet. So far, I have only seen the activated version of RM 2.27.53, and the higher version seems to be using a new encryption method
This is for the MTP3000 series
However, the factory upstart_kernel of the MTM5000 series and MTP3000 series seems to be the same, as I saw that their byte sizes are the same in the same version of...
https://mega.nz/file/Jy9THSgR#jygchkNr5BX7qvcZm-U6iLtt_Xh_kbb2FkoNA-STbBo
This is AIS factory upstart_kernel 1.8.205
PM has been issued
Does anyone have the following version of the factory_upstart_kernel file
Factory_upstart_kernel-1.11.47
Factory_upstart_kernel-1.111.00
Factory_upstart_kernel-1.16.227...
I tried using the password you provided, but on my "R26008661.s19", the decompression software showed that the password was invalid.
Perhaps each file has a different password, or it may involve...
Please check PM
......
In the Z19 software file of MTP3000 series or MTM5000 series models, there is "factory upstart kernel X.XX.XX.bin", but it needs to decompress the password. Can anyone provide this password. I tried...
You can connect the radio station to your computer, then open the "Radio Manager Toolbox" that comes with RM1.81, connect it correctly, select "Information", and wait for the number after...
I think uploading screenshots would be more beneficial for problem-solving
MR 17.2 is actually supported in CPS PLUS 7.4
Yes, I used the programming cable for the front panel interface and checked to ensure consistency between the control head and receiver when upgrading the radio station. I think that's why I blinked...
This is a method of flashing MTM5200 to MTM5400. Here, I take MTM5200 350-390MHz MT853C as an example, as shown in the figure. MTM5200 350-390MHz MT853C and MTM5400 350-390MHz MT853C both have the...