-
Junior Member
Reputation: 10
RET Adjustment on Huawei Platform U2000
Good day All,
Please can anyone share or point me to any document on how to do the RET Adjustment on Huawei U2000 platform.
Many thanks.
BR,
Deekeyz
-
2016-07-31 10:56 PM
# ADS
Circuit advertisement
-
Senior Member
Reputation: 491
Re: RET Adjustment on Huawei Platform U2000
Use MML Command:
DSP RETSUBUNIT
-
Post Thanks - 1 Thanks
-
Member
Reputation: 20
Re: RET Adjustment on Huawei Platform U2000
@deekezy
Enjoy below procedure
Report Type = Scan ALD
Status = Success
Session ID = 65543
Result
------
Control Port Cabinet No. Control Port Subrack No. Control Port Slot No. Control Port No. Result ALD Device Type Vendor Code Serial No. Protocol Version Configure Status Subunit Number Failure Cause
0 60 0 RET SUCCESS SINGLE_RET HW M0997F600SR6400yL AISG2.0 UNCONFIGURED 1 NULL
0 60 0 RET SUCCESS SINGLE_RET HW M0997F600SS334yyR AISG2.0 UNCONFIGURED 1 NULL
0 61 0 RET SUCCESS SINGLE_RET HW M0997F600NR6910yL AISG2.0 UNCONFIGURED 1 NULL
0 61 0 RET SUCCESS SINGLE_RET HW M0997F600NS843yyR AISG2.0 UNCONFIGURED 1 NULL
0 62 0 RET SUCCESS SINGLE_RET HW M0997F600RU5946yL AISG2.0 UNCONFIGURED 1 NULL
0 62 0 RET SUCCESS SINGLE_RET HW M0997F600RV037yyR AISG2.0 UNCONFIGURED 1 NULL
(Number of results = 6)
--- END
+++ HUAWEI 2016-01-14 09:19:04
O&M #667
%%/*800481*/CLB RET:OPMODE=SUBUNIT,DEVICENO=0,SUBUNITNO=1;%%
RETCODE = 0 Progress report, Operation succeeded.
Report Type = Calibrate RET
Status = Start
Session ID = 65544
--- END
+++ HUAWEI 2016-01-14 09:20:54
O&M #671
%%/*800485*/CLB RET:OPMODE=SUBUNIT,DEVICENO=2,SUBUNITNO=1;%%
RETCODE = 0 Progress report, Operation succeeded.
Report Type = Calibrate RET
Status = Success
Session ID = 65546
Result
------
Device No. Subunit No. Result
2 1 SUCCESS
(Number of results = 1)
--- END
O&M #746
%%/*800661*/DSP RET:;%%
RETCODE = 0 Operation succeeded.
Display RET Dynamic Information
-------------------------------
Device No. Actual Vendor Code Actual Device Serial No. Actual Subunit Number Control Port Cabinet No. Control Port Subrack No. Control Port Slot No. Control Port No.
0 HW M0997F600SR6400yL 1 0 60 0 NULL
1 HW M0997F600NR6910yL 1 0 61 0 NULL
2 HW M0997F600RU5946yL 1 0 62 0 NULL
(Number of results = 3)
--- ENDDSP RETSUBUNIT:;
-
Post Thanks - 2 Thanks
-
Re: RET Adjustment on Huawei Platform U2000
if you want to adjust RET use MOD RETSUBUNIT command.Make sure you check the RET supported MAX tilt values using DSP RETDEVICEDATA command to make sure you are not setting tilt beyond device capability.....For TMA use DSP TMA & DSP TMA SUBUNIT to see the Gains.Further you can set the attenunation using MOD RXBRANCH command
Add me Rep to become a Senior Member :)
-
Post Thanks - 1 Thanks
Bookmarks