-
Junior Member
Reputation: 13
How to Improve FER
Dear CDMA Expert Engineer.
KPI Target for FER ( <= 2%) > 90 % ( same for Urban,Suburban,and Rural)
As My Experience, I difficult to improve FER until meet KPI target. the others can meet KPI target like Rx_Power, Ec/Io,Txpower etc.
What the reason can cause bad FER?
How to more improve FER until meet KPI ?
is rational for KPI target for FER (<=2%) > 90%? how about other operator? I want to compare
br//
akur
-
2009-09-30 12:31 PM
# ADS
Circuit advertisement
-
Senior Member
Reputation: 491
Re: How to Improve FER
Dears,
Please share your knowledge
I'm very interested to know about CDMA
-
Senior Member
Reputation: 395
Re: How to Improve FER
![Quote](images/misc/quote_icon.png)
Originally Posted by
kurdi
Dear CDMA Expert Engineer.
KPI Target for FER ( <= 2%) > 90 % ( same for Urban,Suburban,and Rural)
As My Experience, I difficult to improve FER until meet KPI target. the others can meet KPI target like Rx_Power, Ec/Io,Txpower etc.
What the reason can cause bad FER?
How to more improve FER until meet KPI ?
is rational for KPI target for FER (<=2%) > 90%? how about other operator? I want to compare
br//
akur
what about RSSI ? is it within acceptable rang for these sites? for my experience FER<= 2%) > 90 % as a target is high and cant be easy utilized.
to improve the FER you can try the following:
1- reduce the overlab between the sites (antenna para optimization).
2- check and confirm the RSSI/VSWR/BER
2- modify the FER traget in BSC side to 1% if it is 2% (Note: if your network is loaded will affect the capacity)
3- modify the Eb/Nt to optimum value
3- modify fast forward power control according to sites requirents.
Good lock
-
Senior Member
Reputation: 491
Re: How to Improve FER
Thanks a lot aosan,
please guide me as I;m newbie in CDMA
what's Voice Call RX_Power & TX_power?
what's the optimum value for these parameters? and whow to acheive it?
Thanks in advabce
-
Senior Member
Reputation: 395
Re: How to Improve FER
![Quote](images/misc/quote_icon.png)
Originally Posted by
justdream
Thanks a lot aosan,
please guide me as I;m newbie in CDMA
what's Voice Call RX_Power & TX_power?
what's the optimum value for these parameters? and whow to acheive it?
Thanks in advabce
what's Voice Call RX_Power & TX_power?
in general CDMA Voice Call/ 1X DATA, RX_Power >= -95dbm and TX_power<= 0dbm
what's the optimum value for these parameters? and whow to acheive it?
it depend to your drive test analysis and KPI. if your vendor is Huawei then you could have RF parameters tuning guide...i have it somewhere in my HD..i will look for it then share it if possible.
-
Member
Reputation: 211
Re: How to Improve FER
to improve the FER you should check the Ec/Io overall coverage during cluster dt. If Ec/Io > -8 dB (@90% coverage) is less than the target kpi, that's the time that you should optimize the physical side.... are you an RF sir? and in what country? (please add reputation if this one is helpful) thanks
-
Member
Reputation: 53
Re: How to Improve FER
Hello Kurdi, from your explanation, you said that Rx Level, Tx Level and Ec/Io are all good and within threshold but FER is still bad.
If that is the case then the problem can be related to
1) Hardware problems
----Need to check the clocking - (BCKM Board + GPS), this however would affect all sites connected to the BSC
----Need to check VSWR alarm on the sites showing poor FER
Hope you find this useful.........
Regards
Bookmarks