Thanks Thanks:  0
Showing results 1 to 4 of 4

Thread: LTE RRC Connection Reconfiguration event A2 threshold two values purpose

  1. #1
    Senior Member Reputation: 366
    Join Date
    2010-04-12
    Location
    Malaysia
    Posts
    408


    Default LTE RRC Connection Reconfiguration event A2 threshold two values purpose

    Hi guys,

    Wonder if anyone know why the content of RRC Connection reconfiguration message for LTE content 2 event A2 for EUTRAN does it mean one setting for interfrequency event and another one maybe for redirection event?

    {
    reportConfigId 3,
    reportConfig reportConfigEUTRA : {
    triggerType event : {
    eventId eventA2 : {
    a2-Threshold threshold-RSRP : 0
    },
    hysteresis 0,
    timeToTrigger ms256
    },
    triggerQuantity rsrp,
    reportQuantity sameAsTriggerQuantity,
    maxReportCells 8,
    reportInterval min60,
    reportAmount r1
    }
    },
    {
    reportConfigId 4,
    reportConfig reportConfigEUTRA : {
    triggerType event : {
    eventId eventA2 : {
    a2-Threshold threshold-RSRP : 30
    },
    hysteresis 0,
    timeToTrigger ms480
    },
    triggerQuantity rsrp,
    reportQuantity sameAsTriggerQuantity,
    maxReportCells 8,
    reportInterval min60,
    reportAmount r1
    }
    }
    Default Password:finetopix

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many
     

  3. #2
    Member Reputation: 172
    Join Date
    2010-11-01
    Posts
    514


    1 out of 1 members found this post helpful.

    Default Re: LTE RRC Connection Reconfiguration event A2 threshold two values purpose

    depending on mobility algorithms that you have enabled but most probably in your case one of the event is for InterFreq measurements and the other one for InterRAT . In general , event A2 is used for entering compressed mode and measure another LTE layer or Irat.
    BR
    Alex

  4. #3
    VIP Member Reputation: 1767
    Join Date
    2010-04-23
    Location
    Polar Bear
    Posts
    1,031


    1 out of 1 members found this post helpful.

    Default Re: LTE RRC Connection Reconfiguration event A2 threshold two values purpose

    this is just an event that will be triggered for the specific measurement config.
    reportConfigId 3, is triggering when rsrp is worse than -140+hys means it wont happen in any normal scenario. e.g. -140 means there is not connection between UE and BS so no where to send the measurement report.

    reportConfigId 4, is triggering at -110+hys , so when rsrp for specific measure config hits this level it will trigger the measurement report.

    there can be more than one report config per it depends on the vendor algo.

    "E-UTRAN may configure multiple instances of the same event e.g. by configuring two reportingconfigurations with different thresholds."

    read section 5.5 specs.
    https://www.etsi.org/deliver/etsi_ts/136300_136399/136331/09.16.00_60/ts_136331v091600p.pdf



    Also A2 has nothing to do with inter or intra freq. it just measure current serving cell against a threshold.


    Last edited by auto_art; 2022-12-01 at 03:05 AM Reason: addition of information.
    Auto_art Default PAS: london
    pl rate threads for their usefulnes
    share & care

  5. #4
    Senior Member Reputation: 366
    Join Date
    2010-04-12
    Location
    Malaysia
    Posts
    408


    Default Re: LTE RRC Connection Reconfiguration event A2 threshold two values purpose

    Thank you for comment guys.
    I founded out my case the first event A2 is threshold setting for Redirection to other RAT, the second event A2 threshold is for Interfrequency.
    Default Password:finetopix

Tags for this Thread

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •