Thanks Thanks:  0
Showing results 1 to 9 of 9

Thread: can't access to MINI-LINK ((

  1. #1
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default can't access to MINI-LINK ((

    Hi.

    there are several devices that I cannot access.

    MINI-LINK Craft can't connect, when using putty/CLI I get this error:

    Code:
    Linux 2.6.18_pro500-R5G04 ((none)) (ttyp0)
    
    (none) login: root
    Password: 
    
    Login incorrect
    (none) login: admin
    Password: 
    
    Login incorrect
    (none) login: cli
    No directory, logging in with HOME=/
    CLI may be busy ...
    [aprint] Failed to get aprint shared memory, errno=13
    [aprint] aprint shared mem / semaphore preparation failed
    [aprint] Failed blocking signals / locking aprint semaphore!
    
    SYS:../platform/cmo/cm/src/cli_relay-main.c(61)(FLASH:WARM): Error(111): Sorry, can't connect!
    
    [aprint] Failed blocking signals / locking aprint semaphore!
    [aprint] Message not written to flash: WARM:cli_relay:Error(111): Sorry, can't connect!
    as far as I understand it is a software or hardware issue with MTD/JFFS2/Flash/NAND.

    someone faced such a problem ?

    if this software case, how can it be solved ?

    thanks.
    Last edited by carver; 2021-08-04 at 06:16 PM
    /carv

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many
     

  3. #2
    Member Reputation: 69
    Join Date
    2009-04-06
    Posts
    54

    Default Re: can't access to MINI-LINK ((

    Quote Originally Posted by carver View Post
    Hi.

    there are several devices that I cannot access.

    MINI-LINK Craft can't connect, when using putty/CLI I get this error:

    Code:
    Linux 2.6.18_pro500-R5G04 ((none)) (ttyp0)
    
    (none) login: root
    Password: 
    
    Login incorrect
    (none) login: admin
    Password: 
    
    Login incorrect
    (none) login: cli
    No directory, logging in with HOME=/
    CLI may be busy ...
    [aprint] Failed to get aprint shared memory, errno=13
    [aprint] aprint shared mem / semaphore preparation failed
    [aprint] Failed blocking signals / locking aprint semaphore!
    
    SYS:../platform/cmo/cm/src/cli_relay-main.c(61)(FLASH:WARM): Error(111): Sorry, can't connect!
    
    [aprint] Failed blocking signals / locking aprint semaphore!
    [aprint] Message not written to flash: WARM:cli_relay:Error(111): Sorry, can't connect!
    as far as I understand it is a software or hardware issue with MTD/JFFS2/Flash/NAND.

    someone faced such a problem ?

    if this software case, how can it be solved ?

    thanks.
    Hi,

    Which ML product is it...TN or 6600?

  4. #3
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    Quote Originally Posted by bioda View Post
    Hi,

    Which ML product is it...TN or 6600?
    thanks for answer.

    I learned how to reset to CN510, you just need to reset CPU while it's load config. and ulit use default config at next boot.

    but this is CN510 R2 (it differs from CN510, both internally and in firmware). reset don't help.

    possibly in this device - the NAND Flash section is corrupted
    0x08000000-0x10000000: "Util (R / W)"

    I also think this is a universal board and could fit into other MINI-LINK models.
    /carv

  5. #4
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    maybe anyone have work with such a menu before ?
    how to get into it ?

    I also try to load upload files, but I don't see anything in USB and Ethernet ports ((

    Code:
    Started NPU...
    NPU Load Modules ------------------------
       Boot:  CN510R2 CXC1731963_2-R1A17
              Build Date: Apr 22 2013 - 13:17:52(xrserhe)
       PBIST: CN510R2 CXC1731879_2-R1B02
              Build Date: May 15 2014 - 11:14:19(etamjuh)
       Device tree     : CXC 173 5073/1 20130521
       Kernel image 0  : CXP 902 0510/2 R7B126 20160224 170722
       Kernel image 1  : CXP 902 0510/2 R2K12 20150319 175853
    -----------------------------------------
    
    Started NPU...
    
    
    CN510R2 PBIST
    -------------
     D   Display Revision ID     
     S   Short RAM Test          
     L   Long RAM Test           
     F   Firmware Checksum Test  
     M   Flash (NOR/NAND) Test   
     U   User IO Test            
     X   Front Panel Test        
     I   SPI controller Test     
     P   Power Management Test   
     T   Temperature Sensor Test 
     N   Ethernet Test           
     Q   LIU acknowledge Test    
     C   Load and test FPGA      
     K   USB connection test     
     R   Real Time Clock Test    
     E   E1 traffic test         
     Y   Test HARAKIRI#          
     V   Test Board Reset        
     B   OCXO Test               
     O   SmartCard Commands      
     G   Erase Image             
     J   Start U-BOOT
     H   Load files
     *   Autoload programs       
    
    PBIST> H
    
     Load via TFTP (auto mode)
     /  Toggle edit/auto mode
     0  Change TFTP settings
     1  PBIST
     2  Script
     3  BOOT
     4  IMAGE0
     5  IMAGE1
     6  U-BOOT
     7  FDT
     8  FPGA
     9  Exit
    /carv

  6. #5
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    i try some erace in enu,
    here my current my console boot log, but I can't login via CLI.

    Code:
    Started NPU...
    NPU Load Modules ------------------------
       Boot:  CN510R2 CXC1731963_2-R1A17
              Build Date: Apr 22 2013 - 13:17:52(xrserhe)
       PBIST: CN510R2 CXC1731879_2-R1B02
              Build Date: May 15 2014 - 11:14:19(etamjuh)
       Device tree     : CXC 173 5073/1 20130521
       Kernel image 0  : CXP 902 0510/2 R7B126 20160224 170722
       Kernel image 1  : CXP 902 0510/2 R2K12 20150319 175853
    -----------------------------------------
    Start kernel from Active bank: image 0  now...
    
    [    0.000000] Using MPC832x based NPU/CN board machine description
    [    0.000000] Linux version 3.10.75-R1B02-rt80 (mwtnmgr@eselnlx1738) (gcc version 4.7.0 (MontaVista Linux G++ 4.7-150727093217) ) #1 PREEMPT RT Thu Jan 28 15:47:52 CET 2016
    setup_arch: bootmem
    mpc832x_npu_setup_arch()
    arch: exit
    [    0.000000] bootconsole [udbg0] enabled
    [    0.000000] MPC832x CN210 R2 (MPC8323ERDB based)
    [    0.000000] NPU West PCI bus: controller = c03dc000, address = [0x80000000 - 0x9fffffff], buses = [0x00 - 0x0f]
    [    0.000000] Configuring USB pins
    [    0.000000] HAS USB returned 0
    [    0.000000] Zone ranges:
    [    0.000000]   DMA      [mem 0x00000000-0x07ffffff]
    [    0.000000]   Normal   empty
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
    [    0.000000] Kernel command line: root=/dev/mtdblock1 rootfstype=jffs2 ro console=ttyS0,115200
    [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
    [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.000000] Sorting __ex_table...
    [    0.000000] Memory: 125904k/131072k available (3608k kernel code, 5168k reserved, 196k data, 145k bss, 144k init)
    [    0.000000] Kernel virtual memory layout:
    [    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
    [    0.000000]   * 0xfdef9000..0xfe000000  : early ioremap
    [    0.000000]   * 0xc9000000..0xfdef9000  : vmalloc & ioremap
    [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [    0.000000] NR_IRQS:512 nr_irqs:512 16
    [    0.000000] IPIC (128 IRQ sources) at c9000700
    [    0.000000] clocksource: timebase mult[10000000] shift[23] registered
    [    0.000155] pid_max: default: 32768 minimum: 501
    [    0.000472] Mount-cache hash table entries: 512
    [    0.009324] devtmpfs: initialized
    [    0.159928] NET: Registered protocol family 16
                 
    [    0.170253] uc_loader:  UC loader started mpc83xx_ucode_init
    [    0.175920] uc_loader:  QE REV ce100001, core 80670011 80840011 fdefe000
    [    0.182517] uc_loader:  LoadUCodePatch UC size 4084
    [    0.187627] uc_loader:  LoadUCodePatch UC compare done.
    [    0.192740] uc_loader:  LoadUCodePatch REG fdf02100=c00003e5
    [    0.198314] uc_loader:  LoadUCodePatch REG fdf02104=c0000518
    [    0.203888] uc_loader:  LoadUCodePatch REG fdf02108=0
    [    0.208862] uc_loader:  LoadUCodePatch REG fdf0210c=0
    [    0.213836] uc_loader:  LoadUCodePatch REG fdf02110=0
    [    0.218810] uc_loader:  LoadUCodePatch REG fdf02114=0
    [    0.223784] uc_loader:  LoadUCodePatch REG fdf02118=0
    [    0.228759] uc_loader:  LoadUCodePatch REG fdf021f0=20800000
    [    0.235686] PCI: Probing PCI hardware
    [    0.239256] PCI: I/O resource not set for host bridge /localbus@ff405000/pci-west@0xf0040000 (domain 0)
    [    0.249241] PCI host bridge to bus 0000:00
    [    0.253262] pci_bus 0000:00: root bus resource [mem 0x80000000-0x9fffffff]
    [    0.260060] pci_bus 0000:00: root bus resource [bus 00-ff]
    [    0.302504] bio: create slab <bio-0> at 0
    [    0.314351] Switching to clocksource timebase
    [    0.327298] NET: Registered protocol family 2
    [    0.333991] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
    [    0.341132] TCP bind hash table entries: 1024 (order: 2, 24576 bytes)
    [    0.347635] TCP: Hash tables configured (established 1024 bind 1024)
    [    0.354036] TCP: reno registered
    [    0.357209] UDP hash table entries: 256 (order: 2, 16384 bytes)
    [    0.363167] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes)
    [    0.370116] NET: Registered protocol family 1
    [    0.375404] RPC: Registered named UNIX socket transport module.
    [    0.381204] RPC: Registered udp transport module.
    [    0.385834] RPC: Registered tcp transport module.
    [    0.390466] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.400695] mpc8xxx_wdt: WDT driver for MPC8xxx initialized. mode:reset timeout=65535 (8589 jiffies, 34 seconds)
    [    0.422417] Seems like legacy loclabus, skipping elbc init steps!
    [    0.513806] jffs2: version 2.2. (NAND) (SUMMARY)  B) 2001-2006 Red Hat, Inc.
    [    0.528516] msgmni has been set to 245
    [    0.532360] io scheduler noop registered (default)
    [    0.563094] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [    0.574613] serial8250.0: ttyS0 at MMIO 0xff404500 (irq = 16) is a 16550A
    [    0.581429] console [ttyS0] enabled, bootconsole disabled
    [    0.581429] console [ttyS0] enabled, bootconsole disabled
    [    0.593892] serial8250.0: ttyS1 at MMIO 0xff404600 (irq = 17) is a 16550A
    [    0.603775] Freescale QUICC Engine UART device driver
    [    0.608976] ucc-uart: could not register UART driver
    [    0.617250] Trying ONFI probe in 16 bits mode, aborting !
    [    0.622871] ONDIE ECC detected
    [    0.625976] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bit), 256MiB, page size: 2048, OOB size: 64
    [    0.638069] Scanning device for bad blocks
    [    0.940219] Found name: 0x70000000.flash, size: 0x10000000, erasesize: 0x20000, writesize: 0x800, oobsize: 0x40.
    [    0.950468] boot_info = 0x000000e3
    [    0.954223] rootfsoffset from drb is 0x3dd000
    [    0.958626] read kernsize: 0x3dc230
    [    0.962150] FLASH WARN: rootFSoffset updated
    [    0.966476] Root FS offset is 0x003dc23c bytes = 7ba pages = 1f blocks
    [    0.974284] Creating 4 MTD partitions on "0x70000000.flash":
    [    0.980049] 0x000000000000-0x0000003e0000 : "Header/Kernel (R/O)"
    [    0.989896] 0x0000003e0000-0x000004000000 : "Root Disk (R/O)"
    [    0.999498] 0x000004000000-0x000008000000 : "Root Disk (R/W)"
    [    1.009208] 0x000008000000-0x000010000000 : "Util (R/W)"
    [    1.019982] NPU-NOR:0x00800000 at 0x60000000
    [    1.025275] NOR flash on NPUs (8MB): Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x000c01
    [    1.036427] Amd/Fujitsu Extended Query Table at 0x0040
    [    1.041635]   Amd/Fujitsu Extended Query version 1.3.
    [    1.046754] number of CFI chips: 1
    [    1.051550] Creating 4 MTD partitions on "NOR flash on NPUs (8MB)":
    [    1.057896] 0x000000000000-0x000000200000 : "Boot/PBIST (R/O)"
    [    1.067386] 0x000000200000-0x000000400000 : "U-Boot/Env (R/O)"
    [    1.077000] 0x000000400000-0x000000600000 : "Spare (R/O)"
    [    1.086186] 0x000000600000-0x000000800000 : "Crash (R/W)"
    [    1.097982] libphy: Fixed MDIO Bus: probed
    [    1.105010] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
    [    1.111360] ucc_geth_driver: UCC2 at 0xff503000 (irq = 34)
    [    1.119456] PPP generic driver version 2.4.2
    [    1.123848] ML-PPP with MiniLink TN adaptation
    [    1.129623] PPP Deflate Compression module registered
    [    1.135352] qe_udc_probe
    [    1.137959] soc_type: 1
    [    1.141615] fsl_qe_udc ff5006c0.usb: QE USB controller initialized as device
    [    1.149404] g_ether gadget: using random self ethernet address
    [    1.155424] g_ether gadget: using random host ethernet address
    [    1.163196] usb0: MAC 9a:43:50:46:83:84
    [    1.167164] usb0: HOST MAC 6e:30:72:97:86:e8
    [    1.171657] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
    [    1.178333] g_ether gadget: g_ether ready
    [    1.182494] fsl_qe_udc ff5006c0.usb: fsl_qe_udc bind to driver g_ether
    [    1.192154] mpc-i2c ff403000.i2c: timeout 1000000 us
    [    1.200924] TCP: cubic registered
    [    1.208699] NET: Registered protocol family 10
    [    1.217118] NET: Registered protocol family 17
    [    1.226577] TCP: TFO aes cipher alloc error: -2
    [    8.621854] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
    [    8.638251] VFS: Mounted root (jffs2 filesystem) readonly on device 31:1.
    [    8.647699] devtmpfs: mounted
    [    8.652142] Freeing unused kernel memory: 144K (c0362000 - c0386000)
    INIT: version 2.88 booting
    Starting Bootlog daemon: bootlogd.
    Setting up USB DHCP
    [   12.214504] ip_tables: (C) 2000-2006 Netfilter Core Team
    [   12.280935] nf_conntrack version 0.5.0 (1969 buckets, 7876 max)
    [   12.444369] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
    Configuring network interfaces... done.
    Wed Feb 17 15:29:00 UTC 2016
    Starting syslog-ng:.
    Starting flogd:   [ OK ]
    Starting segfaultd:   [ OK ]
    INIT: Entering runlevel: 3
    Starting BDMOD: [  OK ]
    Starting CHKERNEL: [  OK ]
    Starting CH:   [ OK ]
    Starting KUTIL: [  OK ]
    Starting SPI-DRV: [  OK ]
    BACKPLANE=CN
    NPUTYPE=CN510R2
    NPUROLEPROTECTION=PROTECTIVE
    NPUROLEBUS=SLAVE
    NPURAM=126048 kbytes
    KERNEL_VERSION=3.1
    Starting FPGA_LOAD: NPUTYPE=CN510R2
    Starting FPGA Loader TDM CN510R2 [  OK ]
    [  OK ]
    Starting ntpd: done
    Resetting xinetd
    Restarting internet superserver: xinetd.
    Config   TFTP: [ OK ]
    Starting protection driver:  [ OK ]
    Removing start and kill scripts cp: can't stat '*xinetd.*': No such file or directory
    cp: can't stat '*ipr.*': No such file or directory
    cp: can't stat '*hotfix2.*': No such file or directory
    cp: can't stat '*tnipc_dp-ip-client.*': No such file or directory
    cp: can't stat '*hotfix2.*': No such file or directory
    cp: can't stat '*tnipc_dp-ip-client.*': No such file or directory
      [ OK ]
    Installing the RTC device driver: [ OK ]
    System time: Mon Jan  3 23:57:31 2000  0.000000 seconds
    Starting User I/O module: [ OK ]
    Starting PS:   [ OK ]
    MLHC is supported by NERD on this NPUTYPE: CN510R2
    This NPUTYPE (CN510R2) can not handle MLHC in MMUs
    Starting MLHCH: PPC_ipclib::Ipc_receive: No such file or directory
     [ OK ]
    Starting PLH:      [ OK ]
    Config   TFTP:     [ OK ]
    Reseting xinetd
    Restarting internet superserver: xinetd.
    Loading  SPI_DD: (already installed)   [ OK ]
    Starting WDKICKER: [ OK ]
    Protection mode is 1+1 Slave.
    TnIpc started:  TnIpc: [ OK ] Npudd: [ OK ] ip-relay: [ dont start here ]
    INIT: Switching to runlevel: 4
    INIT: Sending processes the TERM signal
    Starting ip-relay:     [ OK ]
    Starting PADS: PADS: Banks: /dev/mtd0 (active), /dev/mtd2 (passive) 
        [ OK ]
    Starting SPI IP Client:[ OK ]
    Loading  EOP: [ OK ]
    
    
       ///\ __///\                            /\\\__ /\\\
      ///\\(  )/\\\      D'Bug Interface     ///\(  )//\\\
     ///     OO  \\\                        ///  OO     \\\
    
         Line: console     Time: 23:57:37     User(s): 0 
    
    freescale-83xx login: 
    
       ///\ __///\                            /\\\__ /\\\
      ///\\(  )/\\\      D'Bug Interface     ///\(  )//\\\
     ///     OO  \\\                        ///  OO     \\\
    
         Line: console     Time: 23:58:12     User(s): 0 
    
    freescale-83xx login: cli
    Password: 
    
    Login incorrect
    freescale-83xx login:
    /carv

  7. #6
    Member Reputation: 205
    Join Date
    2010-08-06
    Posts
    176

    Default Re: can't access to MINI-LINK ((

    you know the login?
    admin_user
    view_user
    ...

  8. #7
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    Quote Originally Posted by pathloss View Post
    you know the login?
    admin_user
    view_user
    ...
    on, These are logins for Mini-Link Craft.
    I't work via SNMP, but it does not see the device ((
    no SNMP service started ((

    I already solder the Nand Flash from another device, but it didn't help (((
    /carv

  9. #8
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    my list of firmwares for CN510.

    1) can anyone share firmware that I don't have?
    2) 0510/2 = CN510 R2. 0510/1 = R1 ??. what is 0510/102 model?


    Code:
    CXP9020510_102_R2B11	CXP 902 0510/102	R2B11	(20140422)	// 102 HW model ???
    CXP9020510_102_R5B114	CXP 902 0510/102	R5B114	(20150313)	// 102 HW model ???
    CXP9020510_1_R4C03	CXP 902 0510/1		R4C03	(20120116)	// no RF FW
    CXP9020510_1_R4E06	CXP 902 0510/1		R4E06	(20120516)	// no RF FW
    CXP9020510_1_R4H01	CXP 902 0510/1		R4H01			// has in unit, but looking update for other !!!
    CXP9020510_2_R2B11	CXP 902 0510/2		R2B11	(20140422)	// no RF FW
    CXP9020510_2_R2F08	CXP 902 0510/2		R2F08	(20140919)
    CXP9020510_2_R2H02	CXP 902 0510/2		R2H02	(20150209)
    CXP9020510_2_R2K12	CXP 902 0510/2		R2K12	(20150319)
    CXP9020510_2_R7B126	CXP 902 0510/2		R7B126	(20160224)
    /carv

  10. #9
    VIP Member Reputation: 1852 carver's Avatar
    Join Date
    2007-10-24
    Location
    Ukraine
    Posts
    563

    Default Re: can't access to MINI-LINK ((

    resolved.

    on board SPI eeprom has byte 0x01 - "SLAVE" mode.
    I changed to "0x00" - MASTER or to 0x02 "STANDALONE" -
    and CLI + CRAFT/SNMP access working OK.

    but still looking for firmware for CN510:
    CXP9020510_1_R4H01 CXP 902 0510/1 R4H01
    /carv

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •