-
How to connect TEMS Investigation with Netgear Nighthawk M1?
Dear Expert,
I tried to connect TEMS Investigation19 with Netgear Nighthawk M1, but it is not worked. Could you please help me how to connect? If it need usb driver, could you support me?
Thank you so much!
Best Regards,
default pw: finetopix123
Let's share to be shared.
-
2017-11-03 01:09 AM
# ADS
Circuit advertisement
-
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
Could you please support me! Thank you so much!
Regards,
Lihanbok.
default pw: finetopix123
Let's share to be shared.
-
VIP Member
Reputation: 1852
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
for work with TEMS or QXDM
Netgear Nighthawk M1 MR1100 need enable DIAG port first.
then you can use defaults AC78xSDrivers
-
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
@carver
Friend Is there any way to enable diagnostic port in HiSilicon modem chipset.
-
VIP Member
Reputation: 1852
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
Originally Posted by
radio_network
@carver
Friend Is there any way to enable diagnostic port in HiSilicon modem chipset.
I recently did it for my old E3276s-500, photo of board here
https://www.4shared.com/photo/OH3gZq...76s-500_1.html
my the firmware was very old, so I found a new one.
also, you need necessarily a regular firmware, Hilink firmware doesn't fit
then use AT command for check current port state:
AT^SETPORT?
^SETPORT:FF;10,3,12
check avaible options
AT^SETPORT=?
^SETPORT:1: 3G MODEM
^SETPORT:2: 3G PCUI
^SETPORT:3: 3G DIAG
^SETPORT:5: 3G GPS
^SETPORT:A: BLUE TOOTH
^SETPORT:16: NCM
^SETPORT:A1: CDROM
^SETPORT:A2: SD
^SETPORT:10: 4G MODEM
^SETPORT:12: 4G PCUI
^SETPORT:13: 4G DIAG
^SETPORT:14: 4G GPS
and just add ports:
AT^SETPORT="FF;10,12,13,14"
of course, you will have other numbers.
On this the ports are enabled, they appear in Device Manager
but as far as I know, after 3G ports enabled,
you need to use Huawei Huut,
and load in a modem - a *.hluf license,
for the work of the Huawei software, or other software.
in theory, these *.hluf files give out huawei,
but as always there are other way.
Last edited by carver; 2018-04-15 at 01:49 AM
/carv
-
Post Thanks - 2 Thanks
-
VIP Member
Reputation: 1852
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
2radio_network
I also have a question.
I was asked a question today, to which I have no answer.
as the program is named, for working with the diagnostic port,
on MTK CDMA processors.
I need an similar QXDM for MTK CDMA.
-
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
Dear Carver,
Could you please tell me how to enable DIAG Port?
Thank you so much!
Best Regards,
Lihanbok.
Originally Posted by
carver
for work with TEMS or QXDM
Netgear Nighthawk M1 MR1100 need enable DIAG port first.
then you can use defaults AC78xSDrivers
default pw: finetopix123
Let's share to be shared.
-
VIP Member
Reputation: 1852
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
2 lihanbok
Only I know who to contact locally in .vn or .ua
-
Post Thanks - 1 Thanks
-
VIP Member
Reputation: 1852
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
anybody can share screenshot of Netgear Nighthawk M1 in the TEMS or NEMO.
I don't really understand what I am writing below ))
but I need screenshot with Nighthawk M1 for
- Band locks functions
- cell lock functions
- RAT locks and
- Layer 3 messages
thanks.
-
Member
Reputation: 289
1 out of 1 members found this post helpful.
Re: How to connect TEMS Investigation with Netgear Nighthawk M1?
For my know, Netgear MR1100 only have RAT Lock, haven't Band lock and Cell Lock.
MR1100 connect TI.jpg
Originally Posted by
carver
anybody can share screenshot of Netgear Nighthawk M1 in the TEMS or NEMO.
I don't really understand what I am writing below ))
but I need screenshot with Nighthawk M1 for
- Band locks functions
- cell lock functions
- RAT locks and
- Layer 3 messages
thanks.
-
Post Thanks - 1 Thanks
Bookmarks