-
BannedUser-MultiAccounts
Reputation: 89
inter-layer handover
dears,
i have a confusion about inter-layer HO,
if we have a normal cell (not concentric) and this cell suffers from TCH and SDCCH congestion on GSM on this cell, we increase or decrease inter-layer HO threshold on DCS to solve GSM congestion ?
-
2012-04-09 05:04 AM
# ADS
Circuit advertisement
-
Member
Reputation: 72
Re: inter-layer handover
that works, inter-ho layer HO threshold change in DCS cell can effects HO Probability from GSM900-DCS1800.
-
BannedUser-MultiAccounts
Reputation: 89
2 out of 2 members found this post helpful.
Re: inter-layer handover
Originally Posted by
jayk
that works, inter-ho layer HO threshold change in DCS cell can effects HO Probability from GSM900-DCS1800.
YES , i know that changing on it will make effect, i need to know i will increase or decrease inter-layer HO threshold on DCS ?
-
Junior Member
Reputation: 11
1 out of 1 members found this post helpful.
Re: inter-layer handover
When the downlink level of a cell is lower than this threshold, the cell takes low priority in handover algorithm. If you increase it, traffic as well as congestion may decrease. This is valid only The layer or level of target cell is lower than that of the service cel
-
BannedUser-MultiAccounts
Reputation: 89
Re: inter-layer handover
Originally Posted by
dgk82
When the downlink level of a cell is lower than this threshold, the cell takes low priority in handover algorithm. If you increase it, traffic as well as congestion may decrease. This is valid only The layer or level of target cell is lower than that of the service cel
ok if we have an example here,GSM higher layer is congested and i need to push traffic on lower layer DCS,i will increase inter-layer HO threshold on GSM to push traffic on DCS ?
-
Member
Reputation: 260
Re: inter-layer handover
Originally Posted by
eng.akhalifa
ok if we have an example here,GSM higher layer is congested and i need to push traffic on lower layer DCS,i will increase inter-layer HO threshold on GSM to push traffic on DCS ?
can u plz mention the vendor
-
BannedUser-MultiAccounts
Reputation: 89
Re: inter-layer handover
Originally Posted by
ventinel
can u plz mention the vendor
the vendor is Huawei.
-
BannedUser-MultiAccounts
Reputation: 155
1 out of 1 members found this post helpful.
Re: inter-layer handover
The equation for inter-layer HO is
Filtered downlink RX level of the target cell ≥ Inter-layer HO Threshold + Adjacent Cell Inter-layer HO Hysteresis - 64
Where "Inter-layer HO Threshold" is cell level parameter and "Adjacent Cell Inter-layer HO Hysteresis" is per relation parameter. So if you want to prefer a specific cell i.e., push traffic from 900 to 1800 of the same site than you should tune "Adjacent Cell Inter-layer HO Hysteresis" instead of "Inter-layer HO Threshold".
Lowering the value of these parameters will cause shift in traffic from source cell to the target cell.
-
Post Thanks - 1 Thanks
-
Member
Reputation: 72
1 out of 1 members found this post helpful.
Re: inter-layer handover
Originally Posted by
eng.akhalifa
YES , i know that changing on it will make effect, i need to know i will increase or decrease inter-layer HO threshold on DCS ?
Increase in GSM900 and decrease in DCS 1800, will shift traffic to DCS1800 cells.
-
BannedUser-MultiAccounts
Reputation: 89
1 out of 1 members found this post helpful.
Re: inter-layer handover
Originally Posted by
maahsan
The equation for inter-layer HO is
Filtered downlink RX level of the target cell ≥ Inter-layer HO Threshold + Adjacent Cell Inter-layer HO Hysteresis - 64
Where "Inter-layer HO Threshold" is cell level parameter and "Adjacent Cell Inter-layer HO Hysteresis" is per relation parameter. So if you want to prefer a specific cell i.e., push traffic from 900 to 1800 of the same site than you should tune "Adjacent Cell Inter-layer HO Hysteresis" instead of "Inter-layer HO Threshold".
Lowering the value of these parameters will cause shift in traffic from source cell to the target cell.
thanks, i think it will help
Bookmarks