MINI-LINK LH

[Wizeguy]

Hi,
Is any expert there care to help me on how to configure ethernet traffic.
What datas am i going to need?
Thank you

BR//
Edmar

What equipment are we talking about here and what do you intend to configure.
L1 or L2, customer bridge or provider?
Resilience?
BW needs?
Synchronization?
DCN?

[wweise]

hey gents, as for the craft they do have Min Link Craft 2.15 out right now aswell...

[spatkad]

What equipment are we talking about here and what do you intend to configure.
L1 or L2, customer bridge or provider?
Resilience?
BW needs?
Synchronization?
DCN?

Please take us through all the Ethernet configuration flavors as listed above on Mini-link TN.
Thanks,

spatkad

[Wizeguy]

Please take us through all the Ethernet configuration flavors as listed above on Mini-link TN.
Thanks,

spatkad

Phew, that is a huge scope you are asking for.
I will need get back on this, maybe just some of it.
What is the prio for you.

[spatkad]

Phew, that is a huge scope you are asking for.
I will need get back on this, maybe just some of it.
What is the prio for you.

You can take your time as you explain. To speed up the explanation, you can use video tutorials. The DCN over Vlan you already explained in the forum.

if possible append the e******* video tutorials. they will make your explanation quick

Thanks,
spatkad

[Wizeguy]

You can take your time as you explain. To speed up the explanation, you can use video tutorials. The DCN over Vlan you already explained in the forum.

if possible append the e******* video tutorials. they will make your explanation quick

Thanks,
spatkad

Hi,
I do not have any videos available.
I will try to make this as a very short an simple guide.
Let me know if it is too simple:

Basic Layer 1 setup in TN4.4FP.
All other settings are considered to be done already.
(DCN, IP-addresses, RL config etc)

This guide is without using wizards.
Remeber to click save after each operation.

1. Expand the Node and then the Ethernet level of the Management tree in MINI-LINK Craft,
by clicking on the "+" signe beside node and then Ethernet.
2. Expand LAN insterfaces and right click on the LAN interface of your choice and select "configure" from the menu.
3. Inteface usage -> connect to layer 1, check that admin status is set to up.
4. Expand your NPU tree and right click on one RL-IME -> select configure
(Alternative for PDH-IME, do the same for PDH-IME under ETU3B/2B)
5. Configure your IME group, RL: add Radio links to be used and PDH: E1:s to be used.
6. Expand the WAN interfaces and right click on the WAN to be used -> select configure general.
Interface usage -> Layer 1. check that admin status is set to up.
7. Click in "Layer 1 connection" under Ethernet in Management tree and then on "add button" at the rightmost corner.
Now select the LAN and WAN interfaces to connect.
8. Done, connection should be up.
Remaining now is to configure QoS, etc.

Good luck

/WG

[spatkad]

Hi,
I do not have any videos available.
I will try to make this as a very short an simple guide.
Let me know if it is too simple:

Basic Layer 1 setup in TN4.4FP.
All other settings are considered to be done already.
(DCN, IP-addresses, RL config etc)

This guide is without using wizards.
Remeber to click save after each operation.

1. Expand the Node and then the Ethernet level of the Management tree in MINI-LINK Craft,
by clicking on the "+" signe beside node and then Ethernet.
2. Expand LAN insterfaces and right click on the LAN interface of your choice and select "configure" from the menu.
3. Inteface usage -> connect to layer 1, check that admin status is set to up.
4. Expand your NPU tree and right click on one RL-IME -> select configure
(Alternative for PDH-IME, do the same for PDH-IME under ETU3B/2B)
5. Configure your IME group, RL: add Radio links to be used and PDH: E1:s to be used.
6. Expand the WAN interfaces and right click on the WAN to be used -> select configure general.
Interface usage -> Layer 1. check that admin status is set to up.
7. Click in "Layer 1 connection" under Ethernet in Management tree and then on "add button" at the rightmost corner.
Now select the LAN and WAN interfaces to connect.
8. Done, connection should be up.
Remaining now is to configure QoS, etc.

Good luck

/WG

Thanks we are waiting for QoS configurations.

spatkad

[Wizeguy]

Thanks we are waiting for QoS configurations.

spatkad

Ah, but I was planning for the L2 customer bridge setting next time.
When I have assembled enough time and will

[Wizeguy]

To follow up on my previous guide for L1 confige, here comes:

Basic Layer 2 customer bridge setup in TN4.4FP.
All other settings are considered to be done already.
(DCN, IP-addresses, RL config etc)

This guide is without using wizards.
Remeber to click save after each operation.

1. Expand the Node and then the Ethernet level of the Management tree in MINI-LINK Craft,
by clicking on the "+" sign beside node and then Ethernet.
2. Right click on Ethernet Switch -> General select customer bridge switch mode
3. Expand LAN insterfaces and right click on the LAN interface of your choice and select "configure" from the menu.
4. Inteface usage -> connect to port 1, check that admin status is set to up.
5. Right click on switch port 1 and select UNI or I-NNI, suggest to use UNI.
6. Expand your NPU tree and right click on one RL-IME -> select configure
(Alternative for PDH-IME, do the same for PDH-IME under ETU3B/2B)
7. Configure your IME group, RL: add Radio links to be used and PDH: E1:s to be used.
8. Expand the WAN interfaces and right click on the WAN to be used -> select configure general.
Interface usage -> port 2. check that admin status is set to up.
9. Right click on switch port 2 and select I-NNI.
10. Right click on Ethernet Switch -> Configure VLAN.
11. Press add VLAN to the right of the table. let port 1 and 2 be members of the same VLAN.
Set VLAN ID of your own choice. Set tagged untagged depedning on the wanted configuration.
12. Done, connection should be up.
Remaining now is to configure QoS, etc.

Good luck

WG

[shabeeh]

Dear I have found 4.4fp alex library but ANSI not ETSI and soon I 'll present.

BR