-
BannedUser
Reputation: 48
Get miss_call message when full signal
Hi pro !
Pls give me ur advice for this problem:
- Sometimes, we get message about miss call from anther MS when we stay in good condition ( full signal, no trans fault). Miss call occur not usual, from MS in same net or different
- But when we called back again, it's ok
- We use Alcaltel System in RAN net ( Viba trans from ALU ), E******* in Core
This problem is not usually, happened in different place
So can u suggest us some solutions for this
Many thks for ur support
-
2011-03-28 12:44 PM
# ADS
Circuit advertisement
-
VIP Member
Reputation: 1795
Re: Get miss_call message when full signal
i am suspecting a faulty MS..
Auto_art Default PAS: london
pl rate threads for their usefulnes
share & care
-
BannedUser
Reputation: 48
Re: Get miss_call message when full signal
Originally Posted by
auto_art
i am suspecting a faulty MS..
Tks for ur feedback
But it happened in different place, and also, diff MS
-
Member
Reputation: 37
Re: Get miss_call message when full signal
Actually it also depends on equipment if the equipment is connected to the tool then it is in auto answer mode which shows a message of miss call from other MS
-
BannedUser
Reputation: 48
Re: Get miss_call message when full signal
Originally Posted by
rishi
Actually it also depends on equipment if the equipment is connected to the tool then it is in auto answer mode which shows a message of miss call from other MS
Sorry, I'm not fully understand ur comments. Did u mean that MS is connected to another equip ( such as PC, phone...) when another MS is calling ? In this case, I don't think miss call message will happen
In my case, MS still in idle mode, free
-
Junior Member
Reputation: 14
Re: Get miss_call message when full signal
Hi,
If you talk about Missed call notification, then the origin is diverse:
- check of course your accessibility in the site, maybe it is degraded.
- check your paging success rate and registration success rate (if the problem is general then the paging in impacted as well)
- if the site location is in RNC border then there might be some ping pong for Location area update resulting in Missed call and UE batterie getting low fast.
- Check as well if you have RRC setup/access failures due to synch (mostly related to transmission or BTS clock)
-check your MHA or ASC (depending on the vendor), maybe faulty (see history if intermittent alarms)
- try to increase the feeder loss compensation, this can improved your accessibility.
- check the E1 errors to be sure it is not from transmission
-check the cabling as well, need to tighten more the connectors and jumpers
- check the noice floor on the sites
- check the VSWR
- ask for the paging from Core as well
- check as well all the cards load in the RNC
BR//
-
Member
Reputation: 19
Re: Get miss_call message when full signal
Hi, I have a lot of questions for locating source of problem:
Did you have any A interface traces?
If you have, whats seen in them?
Is problem happening in one particular LAC/BSC/MSC?
Is problem happens for some specific phone types or in some particular hours.
What is you paging strategy (IMSI, TMSI, repeated Paging).
Are you using Gs or DTM?
When MS is reached with second call, does it answer first or second page and with TMSI or IMSi?
Try, using TEMS, make many (a mean really really lot of calls at different times) repeated calls to any MS and check if all of them reaches MS.
-
VIP Member
Reputation: 1795
Re: Get miss_call message when full signal
put imsi trace & then check for the msgs..!! this wil help u out..
Auto_art Default PAS: london
pl rate threads for their usefulnes
share & care
-
Re: Get miss_call message when full signal
Hi Guys,
Actually i observed this problem in our network also. Some of the reason are:
1. Pilot pollution on the area
2. Multi Server problem
3. Missed 3G/2G neighbor definition
4. Ping Pong in Idle mode
For 3 first case try to optimize coverage and restrict overshooting cells
for 4th case define IRAT relation and check inconsistencies in between 2G and 3G network
Please share your experiences
-
Senior Member
Reputation: 307
Re: Get miss_call message when full signal
I don't think the issue is in the RF interface - suspect media gateway... but that needs extensive tracing.
Bookmarks