Search:

Type: Posts; User: luinux123; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    4,929

    Re: Request for M-Fiol Software

    19.


    Thanks Zeuscane, but this version is too old, do you have the last version of M-Fiol, this version is not working with new models of RBS. The last versión es 4.19.28

    Thanks Again!
  2. Replies
    4
    Views
    4,929

    Request for M-Fiol Software

    Hi Guys,

    There is some full version of M-FIOL available on the forum?
    I have not been able to find it is an excellent tool for GMS.

    Thanks!!!
  3. Replies
    0
    Views
    1,970

    Actix Analyzer Last Versión [Request]

    Hi Everybody,

    Could someone share with me one license and installer of the last version of ACTIX Analyzer?

    Thanks alot!!!
  4. With what type of exterior paint can I paint an antenna

    I need to paint an antenna because I'm going to install it on a facade and I have to paint it the color of it. Is there any special exterior paint I can use?
  5. Question About Cell Jammers for Prision Area

    Hi Everybody,


    I'm looking for Cell Jammers to block jails or prisons areas that are 100% effective. Outdoor equipment should be preferably and protected, that block the best possible limited...
  6. Replies
    0
    Views
    1,046

    GUIDE FOR NEXPLORER - [REQUEST]

    Hello Guys,

    Somebody can share the Guide, Tutorial or Manual to use Nexplorer?

    I will Apreciate.


    Regards.
  7. Replies
    0
    Views
    2,981

    Draw Sector in KML

    Hi,

    Somebody can helpme... I try to make a autoupdated file in GoogleEarth with Azimuths, conected to some DB.

    My firts problems is... is there some fuction or procesure to draw... because......
  8. Replies
    8
    Views
    4,419

    Re: Nexplorer 14.2 & MCOM 14.2

    Hi everyone,

    Can you share some tutorial to use this tool, please.

    I´ll give you rep an thanks.

    Regards.
  9. Replies
    2
    Views
    2,234

    New version M-Fiol 3.13.4 (Installer Only)

    Hello Friends,

    This is a new version of M-Fiol (installer only), a perfect tool to manage 2G.


    https://mega.co.nz/#!nZAEHBpZ!MOqJOO_EjGysIBjAUZr2UCgnSCKCYLNEjWwg66VnBOc



    M-fiol ...
  10. Re: Low Throughput in E// HSDPA in Idle Mode Good Througput on call

    Somebody have any idea?
  11. Low Throughput in E// HSDPA in Idle Mode Good Througput on call

    Dear Experts, I have a big problem, I need your help.... I have an E// Network with HSDPA and H+, but it result that when a try to test internet net speed in idle mode the throughput is really...
  12. Replies
    4
    Views
    2,764

    Re: HOW TO INVESTIGATE LOW HS THROUGHPUT

    Do you have some similar file for E//????
  13. Replies
    0
    Views
    3,170

    How to calculate balance into C1 and C2???

    Dear Experts,

    I need your help, I dont know how to calculate this parameters to balance traffic between C1 and C2... how can I calculate the value... for this parameters???

    lset...
  14. Replies
    3
    Views
    3,651

    Re: Problems with a Dummy Cell

    Somebody have any idea?
  15. Replies
    3
    Views
    3,651

    Problems with a Dummy Cell

    Dear Experts,

    I need your help, I have configured a dummy cell to block calls in a penal institution, the dummy works fine, but there is a phone brand AMGOO model AM 103 that ignores these...
  16. Replies
    1
    Views
    1,494

    How to set a Dummy Cell in UMTS E*******

    Friends,

    I need your help, how can I set a Dummy Cell in UMTS E******* to block CS y PS in a Prision Area.

    - ¿How block Call Origination?
    - ¿How to block Calls for SHO?


    ¿Parameters that...
  17. Replies
    10
    Views
    5,387

    Re: Request for Exert that runs by 64bit & Win7

    You need to install a Office 2010 or 2007 for 32 bits in you Win7 x64...
  18. Replies
    2
    Views
    2,260

    Re: Two RBS2111 with Two E1´s

    Thanks MAZ29... for your answer, but remember that RBS2111 have only Port A / Port B...

    But I resolve the problem conect 1st E1 in Port A (MASTER) 2nd E1 Port B (Slave) and Sinconization wire PORT...
  19. Replies
    2
    Views
    2,260

    Two RBS2111 with Two E1´s

    Hi Dear Experts,

    Please tell me it is that possible... I have two RBS2111 one Master and one Slave with sync cable... Initially RBS were working both wired sync with an E1, but required additional...
  20. Replies
    9
    Views
    7,794

    Re: I'm telecom engineer, I have no life.

    I also I had so much fun in the page, we all live the same situations regardless of location. And I think most of us have thought: "" I need to change my job" LOL
  21. Replies
    9
    Views
    7,794

    Re: I'm telecom engineer, I have no life.

    Thanks Piojo... Happy labor day for you too...!!!
  22. Replies
    9
    Views
    7,794

    I'm telecom engineer, I have no life.

    Hi Friends,

    Just for fun, here will be able to find and upload some pictures Funny about our situations we work daily in Telecom

    https://www.facebook.com/imtengineer

    I hope you enjoy it.
    ...
  23. Replies
    3
    Views
    2,205

    Re: How to Activate TCC in RBS2111

    Thanks Redendo,

    Very useful but this file is only for RBS2106/2206... and I need especifications for implement TCC in RBS2111...
  24. Replies
    3
    Views
    2,205

    Re: How to Activate TCC in RBS2111

    Can Somebody help me with this question, please???
  25. Replies
    3
    Views
    2,205

    How to Activate TCC in RBS2111

    Hi Experts,

    Can somebody explain to me, please, how can I do to activate TCC Feature in RBS2111 (E*******)??, I read that it is posible but I dont know, how can I do to balance Downlink and...
Showing results 1 to 25 of 101
Page 1 of 5 1 2 3 4