Hi,
Could try a simple test for TX limitation but you need 2 users & 2 Ue to test but second Ue (and user) can be regular one.
1. Start download with your test Ue on one sector, let it get to max...
Type: Posts; User: bawbag11; Keyword(s):
Hi,
Could try a simple test for TX limitation but you need 2 users & 2 Ue to test but second Ue (and user) can be regular one.
1. Start download with your test Ue on one sector, let it get to max...
Hi,
My comment having tried similar is good luck, you will need it :) Lots of old junk out there embedded in all sorts of kit use 2G only. Many new Iot products (think bike hire company) use 2G...
Hi,
1. Camping was allowed on both carriers so users who got onto the 5MHz one had poor performance in comparison to 10MHz, you can configure differently of course however the whole cell layer...
Hi,
No experience on 1900, but on 2100:
Tested overlap carriers however it was not any real benefit. With 1x10MHz + 1x5MHz overlapped by 600kHz the performance on both were OK with no load but in...
Normally WIPS will not allow neighbour without priority set. The priority is used in soft handover when neighbour list concatenation happens and you get the highest priority ones sent in the...
Not seen this posted before so here is link (installer only) for Atoll 64 bit ver 3.2.1.6837. Apologies if duplicate.
RAR file password is atoll ---> atoll6837.rar (4shared, 78MB)
BB
Hi,
I would definitely do a loopback test to double check the TX circuit. If TX Network is IP you are using pseudowire and too many times the TX people avoid setting the correct CIR rate end to...
1) what are the immediate practical outcomes of an E1/T1 active alarm Or clock sync alarm? Audio distortion and lost signalling possibly leading to dropped calls / SHO failures and call setup...
Use Query Result in M2000 to show neighbour statistics. This includes SHO attempts / success for both configured and also detected neighbours that have been added to active set (assuming you have...
Made no difference in my network. Seems more config work for no gain. Currently we have it off. Irat performance ok as long as PS on the GSM cell is not congested. Check usual suspects on the GSM...
If the other cells are working OK check allocation of BB resource. if the other cells are not working then reset the NodeB, still no then check the config. Is the NodeB connected by Ethernet or E1?...
Hi Polo, I cannot attach in one part as it is too large (max attach 3.8MB) and splitting would make more than 10 parts. is there any file sharing site that you can access and I will upload it there?...
Apologies if already posted..
Wray Castle RP2400 Introduction to UMTS Optimization
Link:4shared.com [47MB]
password: finetopix.com
AFAIK:
MaxPCPICHPower & MinPCPICHPower are only of use when you use LDC/R algo. In my network the setting are left as default as we dont use the PCPICH for load control:
List PCPICH...
Do a UEXT2GCELL & check correct BCCH / BSIC etc. Double check in BSC it is same.
Check U2GNCELL for the neighbour relation and see if it is ok.
Check UCELLINTERRATHOCOV is blank or same as other...
From my experience you need to do 3 things:
1. Maintain G900 coverage at all costs, if not the customer will complain.
2. Deal with overshooting cells, tilt etc while trying not to affect point 1...
Hmm:
Seems to have all the files required?
ftp://huntervalleyaviation.com.au/Mentum_VHA/
BR
Interesting, Seen some issues where phone will camp on foreign network but when manually search it does not find the home network but this was timing. If your getting no network access and the radio...
Large difference in network timing between two networks?
Whats the error message on the phone when manually register with home network after amped on neighbour country cell?