Search:

Type: Posts; User: Muhammad; Keyword(s):

Search: Search took 0.00 seconds.

  1. Re: LZU1082505 - RAN Architecture Evolution To 5G

    "www.finetopix.com" is the pass
  2. Re: 5G Beamforming details in both in C-band and Mmwave

    Hi Dear
    Can you please share again. The link is unavailable
  3. Re: Interference in the 800 Mhz LTE, 20 Mhz bandwith

    The most frequent sources in 800 MHz band are due to the PIM or CATV leakage (In case you have Cable TV networks in your country). The Audio component of the TV signal spans over 200 ~ 400 Khz. check...
  4. Re: Interference in the 800 Mhz LTE, 20 Mhz bandwith

    Can you share the exact frequencies of the UL bandwidth in your region.
  5. Replies
    6
    Views
    4,637

    Question Re: LTE 20W and 40W

    Power Boost refers to increasing the Reference Signal power by the calculated amount (10 log(1 + Pb)). The total transmit power remains 20 watts but you can achieve greater coverage. However, the...
  6. Replies
    6
    Views
    7,494

    Re: UL interference in LTE

    This formula works on the background Noise and bandwidth of signal only.

    BR
    Jamil
  7. Thread: IRAT problem

    by Muhammad
    Replies
    7
    Views
    3,215

    Re: IRAT problem

    External LAC definition are done at the core side if 2G and 3G MSC are different. In this case the wrong definition or no definition may lead to IRAT failures. Actually the MSC has no info to route...
  8. Thread: IRAT problem

    by Muhammad
    Replies
    7
    Views
    3,215

    Re: IRAT problem

    Actually this sort of issue is faced when your External cell definitions at 3G end are not consistent with 2G side. Either the mismatch in Cell ID, LAC / BSC ID may lead to IRAT HO failures. If this...
  9. Replies
    6
    Views
    7,494

    Re: UL interference in LTE

    Actually the RSSI should be calculated as

    Noise floor (RSSI) = -174 + Noise Figure (Equipment specific) + 10 log (Bandwidth)

    In LTE a RB consists of 180kHz so 10 log (180,000) =...
  10. Question Re: CDMA 1X & EVDO Drive Test parameters definitions???

    Repo Please if it helps you.
  11. Replies
    42
    Views
    10,289

    Original Re: CDMA the BSS MAINEX AAT V100R004

    Can you please upload this again. I am in need of this tool, please.

    BR
  12. Replies
    7
    Views
    2,263

    Re: Question: BSC6900 UMTS Subrack Capacity

    Check for the SPU capacity as well. I think in such SPU capacity will be less than DPU boards.

    BR

    Repo please if it helps you.:(
  13. Replies
    1
    Views
    1,587

    Question Re: DPUd board Query

    Actually in CDMA/EVDO DPUDb boards have the limitations of two types

    Simultaneous connections
    Flux as DPUDb board in CDMA can support upto 190 Mbps of combined flux (in upload and download...
  14. Replies
    6
    Views
    2,737

    Question Re: How to check IP address with mml command ?

    In Huawei, LST BTSLNK
  15. Re: Why Control Channels Power is Lesser than CPICH Power

    Because when the UE or MS starts acquisition, it has no synchronization info so to enable a MS to successfully decode and detect CPICH or Pilot channel, The transmit power of CPICH in WCDMA and Pilot...
  16. Question Re: Need help to unlock Huawei internal documents

    Dear Can you upload these on 4shared
  17. Download Re: Very Good Optimization Course For CDMA engineer

    can you please upload these on 4shared
Showing results 1 to 17 of 17