drive test car - small table for SW (TEMS/NEMO) monitoring engineer with laptop

Dear forum experts,

please, can you send some photo for ideas - for drive test car - small table for SW (TEMS/NEMO) monitoring engineer with laptop

I am wondering what solution has someone made for the comfortable long hours drive testing and having laptop in front of engineer.

Thanks for any idea.

P:)

Hi Friend,

try something like below bag packs, in my understanding they come with Fans and connection to power supply too

https://www.dingli.com/PilotWalktourPack.php
http://pentacell.net/en/DriveTest.html

Thanks justdream,

very useful info, but still I need someone to send few photos of ideas - for drive test car - how they made a small table for laptop , for the engineer with laptop
that sits next to the driver in front seat and monitors data collection SW (TEMS/NEMO) for long hours.

Thanks for any idea !
P:)

Hi!
A lot of ideas. But, it should be possible to implement the idea.
look here:
1. Top Eight Frequently Asked Questions about RF Drive Testing - everything RF
2. How to set up Your TEMS Kit Tutorial - YouTube
3. Drive test #telecom #tems - YouTube
4. Attachment 43848
5. Attachment 43849
6. Attachment 43850

Budget option: you take 3 - 5 smartphones with TEMS™ Pocket installed, place them in your pockets and use a company car (or public transport) to complete a trip along a given route. Traveling by public transport gives a more accurate picture.

Quote:

---

Originally Posted by punto

Thanks justdream,

very useful info, but still I need someone to send few photos of ideas - for drive test car - how they made a small table for laptop , for the engineer with laptop
that sits next to the driver in front seat and monitors data collection SW (TEMS/NEMO) for long hours.

Thanks for any idea !
P:)

---

No tables required, just a mobile rack like below one:
Engineer sits next to driver and put it in front of him and enjoy monitoring the 6 ~ 8 mobiles in the same moment,
they have fans and can be connected to power supply

Thanks to all,

please, does anyone also has some photo to add, for small table to place a laptop at the place of co-driver , for measurement monitoring engineer ?
Air bag needs to be switch off , obviously in fron of co-driver`s seat ..

Hi!
Real experience in operating Test Drive equipment (batteries, voltage converter, laptops, test phones, GPS antenna).
A car was purchased - a van, with factory design changes:
a stainless steel protective shield near the tailgate and a folding table near the seats in the cabin.

The terms of reference for the design change were unsuccessful. Batteries closed the hatch with a spare wheel.
(additional batteries with a capacity of 100 Ah for the converter 12 - 220 volts nearby).
There was no fastening for fixing the batteries (as a result, the batteries moved around the cabin while driving).
The laptop table, test phones, as well as all the installed items on it vibrated during movement.
These problems were not the most important.
During the period of operation, the hard drive of the laptop failed a couple of times.
The laptop's USB ports were destroyed due to the constant removal and installation of USB cables to test phones.
Cases and connectors of test phones were damaged due to falls from the table.
The 12-220 volt converter for powering laptops failed.
The GPS antenna was installed on the roof of the car and went out of service due to factory defects and damage to the antenna cable and connector.
The car did not have four-wheel drive and there was a restriction on its use off-road with good coverage.
It was a very bad decision.
Based on the foregoing, it is necessary to draw up the correct terms of reference, which provides for the following:
1. use the type of transport.
2. use and placement of test drive equipment in the car.
3. using power supply for TD equipment.
You can probably add some more requirements, for example, vibration absorption devices, etc.
Important: create a 3D model of all devices in the car. This is design work.
It is not realistic to send photos of unsuccessful decisions.

We used some RAM Mounts instead of tables. Very stable and easy to fit. Sorry no photos. Try product pages on their website

https://rammount.com/pages/laptop-mounts

Thanks Slava and phila63 ...