xcal-m setup (v3.3.6.121) and xcap-m-5.12.1.0 installers only

Hi guys this time I would like to share with you xcal-m (v3.3.6.121) and xcap-m-5.12.1.0 installers only in this file you will also find additional patches to install after the installation of each set up , I must say that I am only sharing the set up files I do not have the med or any licgen, perhaps someone in the forum can help to create an emulator for these two softwares. in my particular case I Need and emulator for xcal-m setup (v3.3.6.121) and xcap-m-5.12.1.0 that has LTE SEQUANS CHIPSET integrated.

here is the link to download:

https://mega.nz/#!uApRQKbY!acSbTrlos...3OMc3UWjY24PfU

password to unrar files: www.finetopix.com

I hope some expert in this matter can give us a hand with med for these softwares I will really appreciate if someone can help me.

BR...

The download link has been updated enjoy...

thx for share
does these tool deserve the effort , can u give an idea about their benefits

yes, It is a very good drive testing and post processing tool but as you can see the only thing that I do not have is the med...

License (XCAL-M, XCAP-M) and emulator (x86, x64) attached below.

After installing them
Photo_1
the XCAL-M 3.3.6.131 starts smoothly
Photo_2

Quote:

---

Originally Posted by Jose1975

in my particular case I Need and emulator for xcal-m setup (v3.3.6.121) and xcap-m-5.12.1.0 that has LTE SEQUANS CHIPSET integrated.

---

You can try to install your expired license for LTE Sequans chipset with the emulator found by me. This emulator works with the expired license found by me
Photo_3
Therefore, there is a chance that it will work with your expired license.

Example:
The Netgear AC810S (locked to the configuration CA_3_20 using QXDM NV Browser - info) connected to the XCAL-M 3.3.6.131
Attachment 40823
Attachment 40824
Attachment 40825
Attachment 40826

Requests to forum members:
1. From the helpdesk
http://help.usa.accuver.com/helpdesk/
it follows that there are available newer XCAL-M 3.4.0.x versions from 2017. If someone has a XCAL-M 3.4.0.x, please share it on the forum.
2. The license found by me supports LTE Qualcomm chipset with 2CA
Photo_8
If someone has a license which supports LTE Qualcomm chipset with 3CA, please share it on the forum.
3. The license found by me does not support LTE Samsung chipset (Exynos) and LTE HiSilicon chipset (Balong). If someone has a license which supports LTE Samsung chipset (Exynos) or LTE HiSilicon chipset (Balong), please share it on the forum.
4. Consider adding a reputation for me. The working XCAL-M 3.3.6.131 from 2016 (and probably also the XCAP-M 5.13.51.0 - I have not installed and tested it) shared by Jose1975 definitely deserves for that.

Thanks :)

Download

Quote:

---

Originally Posted by engine-driver

License (XCAL-M, XCAP-M) and emulator (x86, x64) attached below.

(and probably also the XCAP-M 5.13.51.0 - I have not installed and tested it)

Thanks :)

---

not work for XCAP-M 5.13.51.0:(

Hi engine-driver & All

After careful application of installation steps 'xcal-m setup (v3.3.6.121) and xcap-m-5.12.1.0' explained in packages provided by Forum. I'm unable to successfully activate either
XCAL-M or XCAP-M using the license keys provided on my Windows 7 Ultimate - 64bit PC. As seen below, complete with Sentinel v768 already installed.

PS - also observed "Device Driver Notifications - Not Appearing as normal'

Attachment 40828

Could someone please help me with this application & license

REGDS Jesterbean

@hiran
please upload XCAP-M 5.13.51.0

Quote:

---

Originally Posted by Jesterbean

PS - also observed "Device Driver Notifications - Not Appearing as normal'

Attachment 40828

---

Jesterbean, thanks for information. I will check the problem tomorrow.

----------------------------------------------------------------------------------------

From the screenshoot it looks that the problem is DSEO. There is a mistake in an original guide, which I didn’t notice earlier. You should type
C:\Windows\System32\drivers\multikey.sys
under ‘‘Sign a System File’’.

To load Test Mode on Windows 7 x64, I personally use the _prereqSet64v3.cmd script known on the forum (attached below). This is much easier method for me
https://www.raymond.cc/blog/loading-...ta-64-bit-x64/

Summarizing, the most important step is to run Install.cmd as Administrator. This will install Virtual USB MultiKey, SafeNet USB SuperPro/UltraPro
Virtual USB MultiKey
SafeNet USB SuperPro/UltraPro
and add the registry file 00008ED7.reg to the Windows registry
MultiKey Dumps 00008ED7

Check these 3 items now and after Windows restart. Having Java installed you can also check the address
http://localhost:6002

Now, the program should work.

Quote:

---

Originally Posted by tester

@hiran
please upload XCAP-M 5.13.51.0

---

here is the link to download:

Quote:

---

Originally Posted by Jose1975

https://mega.nz/#!idgUkJAC!4cCCmozNH...lZli-BvEmKOnlk

password to unrar files: finetopix

---

how to connect qualcom based datacards/phones
dm port/at port/modem port
could not suceedm
Any help pl