yazzzing
2009-12-25, 10:51 AM
I read this article and emulate some hasp hl success,so I post it,I wish it can help others to emulate hasp hl by himslef......If someone need tools,I can upload,and if have questions,you can ask,but what I'm know is limited,I can only guide in door.....
D-u-mping Hasp HL keys
How can be emulated hasp HL max http://www.aladdin.com/hasp/max.aspx . It works of course for Pro and Time.
What we need:
a key
d-u-mper – i used h5dmp.exe
TORO hasp monitor
Sataron’s UniDMP2reg convertor
emul-ator – i used Chingachguk vusb emu-lator
1. So at first, install dongle drivers, connect a dongle, run Toro monitor.
2. start your protected application and used it.
3. in TORO monitor you will see password for your key and memory of your du-mp. So use your protected software as usual, try to open all menus and dialogs, use every function …
4. Save log file, and save log file.
5. use du-mper and du-mp the key. Result will be – two files hasp.dmp (about 790 B in my case) and hhl_mem.dmp (about 4 KB).
6. then use Sataron’s Unidu-mp2reg and make a reg file (use vUSB Hasp HL option). You can edit this regfile and change licensing of your program (if it uses – hl max can be used for 112 programs)
7. And now the most important thing. Hasp HL uses enveloping technology with 128-bit AES symmetric encryption engine on key.
In TORO log we will find pairs. They can be found in the pairs window too.
Instructions can look like this one:
Code:
HaspHL In:> Hasphl_decrypt, Length=32
Data:
4284 ... ... ... 84ADA4 – It is a question for hash key
HaspHL Out:> Hasphl_decrypt Status=0 (0x0)
Response:
8222 ... ... ... 84ADA4 – And the key respond – it is his answer(I remove part of code)
So what we will do with it? We will do Q/A table. This is Questions and Answers table in reg file. I added it on the end of file.
Data or question of IN – write in Qtable
Response or answer or OUT – write in Atable
Data shoul be write in pairs like these: 4284 ... ... ... 84ADA4 should be write: 42,84, ... ... ... 84,AD,A4
The end of regfile shoul look:
Code:
... regfile
"QTable"=hex:\
42,84,... 84,AD,A4,\
"ATable"=hex:\
82,22,C2 ... 84,AD,A4,\Your program can use only one Q/A or too many. You must add them all. Then you can save your regfile.
8. Add reg file into registry
9. unplug your dongle
10. Install Chingachguk & Denger emu-lator, vusbbus.sys must be 0.15 or above. If all went fine, new device Hasp HL was found.
11. Your program should run
I hope, this text will help.
Vusb 0.15.1.4 can handle encrypt function too.
For a large Q/A pairs from Toro Emu-lator, you can use splitter.
D-u-mping Hasp HL keys
How can be emulated hasp HL max http://www.aladdin.com/hasp/max.aspx . It works of course for Pro and Time.
What we need:
a key
d-u-mper – i used h5dmp.exe
TORO hasp monitor
Sataron’s UniDMP2reg convertor
emul-ator – i used Chingachguk vusb emu-lator
1. So at first, install dongle drivers, connect a dongle, run Toro monitor.
2. start your protected application and used it.
3. in TORO monitor you will see password for your key and memory of your du-mp. So use your protected software as usual, try to open all menus and dialogs, use every function …
4. Save log file, and save log file.
5. use du-mper and du-mp the key. Result will be – two files hasp.dmp (about 790 B in my case) and hhl_mem.dmp (about 4 KB).
6. then use Sataron’s Unidu-mp2reg and make a reg file (use vUSB Hasp HL option). You can edit this regfile and change licensing of your program (if it uses – hl max can be used for 112 programs)
7. And now the most important thing. Hasp HL uses enveloping technology with 128-bit AES symmetric encryption engine on key.
In TORO log we will find pairs. They can be found in the pairs window too.
Instructions can look like this one:
Code:
HaspHL In:> Hasphl_decrypt, Length=32
Data:
4284 ... ... ... 84ADA4 – It is a question for hash key
HaspHL Out:> Hasphl_decrypt Status=0 (0x0)
Response:
8222 ... ... ... 84ADA4 – And the key respond – it is his answer(I remove part of code)
So what we will do with it? We will do Q/A table. This is Questions and Answers table in reg file. I added it on the end of file.
Data or question of IN – write in Qtable
Response or answer or OUT – write in Atable
Data shoul be write in pairs like these: 4284 ... ... ... 84ADA4 should be write: 42,84, ... ... ... 84,AD,A4
The end of regfile shoul look:
Code:
... regfile
"QTable"=hex:\
42,84,... 84,AD,A4,\
"ATable"=hex:\
82,22,C2 ... 84,AD,A4,\Your program can use only one Q/A or too many. You must add them all. Then you can save your regfile.
8. Add reg file into registry
9. unplug your dongle
10. Install Chingachguk & Denger emu-lator, vusbbus.sys must be 0.15 or above. If all went fine, new device Hasp HL was found.
11. Your program should run
I hope, this text will help.
Vusb 0.15.1.4 can handle encrypt function too.
For a large Q/A pairs from Toro Emu-lator, you can use splitter.