krobelux
2017-12-01, 12:05 PM
New release from atoll, installer only
X64 Installer (https://mega.nz/#!KJ0SkahT!lsKIrp6Rku-96MJSiIDJxR8ET8f2v9FEhYcdjNqmVmI)
32Bit Installer (https://mega.nz/#!yE8nGY6b!ZlTNTWi-oTeVkOiJOjA_GA4BlSv0xBG0aJ6kexthNp4)
Release Note for Release 12009 (28 November 2017)
General Features
Licensing
• Handling of measurement licenses has been improved.
Atoll Management Console
• The management of data modifications history through the Atoll Management Console is now available for Microsoft SQL Server
databases.
User interface
• You can now use the Filter by Selection and Group by Selection context menus directly from a single site. This enables you to quickly filter
or group transmitters of a single site.
Geo Data
• Support for the Rikets koordinatsystem 1990 (RT90) coordinate system has been added.
Antennas
• An option has been added to support higher precision (0.1 degree) antenna patterns, primarily for microwave antennas. You can enable
this option by setting the HighResolutionAntennaPattern parameter in the [Antenna] section of the Atoll.ini file.
Automatic Cell Planning
• The UL Signal Level quality objective is now available for LTE networks.
• An option has been added to consider a pattern electrical tilt equal to zero degrees. You can enable this option by setting the
CalculateEtiltWhenZero parameter in the [ACPMisc] section of the ACP.ini file.
Radio Calculations
ITU 1546 Propagation Model
• The three following parameters from the ITU 1546 recommendation can now be configured:
• Correction for receiving/mobile antenna height.
• Cluttered transmitter correction.
• Terrain clearance angle correction.
Traffic and Capacity Planning
Simulations
• You can set the precision of the global scaling factor in a simulation by setting the GlobalScalingFactorDigitsNumber parameter in the
[Simulation] section of the Atoll.ini file.
LTE and NB-IoT Networks
LTE
• Support for up to 128 antennas, i.e., 16, 32, 64, and 128, as a first step towards massive MIMO modelling.
Network Configuration Using the AFP
• It is now possible to select the technology for which you want to perform automatic frequency planning, LTE or NB-IoT, directly in the AFP
window.
X64 Installer (https://mega.nz/#!KJ0SkahT!lsKIrp6Rku-96MJSiIDJxR8ET8f2v9FEhYcdjNqmVmI)
32Bit Installer (https://mega.nz/#!yE8nGY6b!ZlTNTWi-oTeVkOiJOjA_GA4BlSv0xBG0aJ6kexthNp4)
Release Note for Release 12009 (28 November 2017)
General Features
Licensing
• Handling of measurement licenses has been improved.
Atoll Management Console
• The management of data modifications history through the Atoll Management Console is now available for Microsoft SQL Server
databases.
User interface
• You can now use the Filter by Selection and Group by Selection context menus directly from a single site. This enables you to quickly filter
or group transmitters of a single site.
Geo Data
• Support for the Rikets koordinatsystem 1990 (RT90) coordinate system has been added.
Antennas
• An option has been added to support higher precision (0.1 degree) antenna patterns, primarily for microwave antennas. You can enable
this option by setting the HighResolutionAntennaPattern parameter in the [Antenna] section of the Atoll.ini file.
Automatic Cell Planning
• The UL Signal Level quality objective is now available for LTE networks.
• An option has been added to consider a pattern electrical tilt equal to zero degrees. You can enable this option by setting the
CalculateEtiltWhenZero parameter in the [ACPMisc] section of the ACP.ini file.
Radio Calculations
ITU 1546 Propagation Model
• The three following parameters from the ITU 1546 recommendation can now be configured:
• Correction for receiving/mobile antenna height.
• Cluttered transmitter correction.
• Terrain clearance angle correction.
Traffic and Capacity Planning
Simulations
• You can set the precision of the global scaling factor in a simulation by setting the GlobalScalingFactorDigitsNumber parameter in the
[Simulation] section of the Atoll.ini file.
LTE and NB-IoT Networks
LTE
• Support for up to 128 antennas, i.e., 16, 32, 64, and 128, as a first step towards massive MIMO modelling.
Network Configuration Using the AFP
• It is now possible to select the technology for which you want to perform automatic frequency planning, LTE or NB-IoT, directly in the AFP
window.