How to connect TEMS Investigation with Netgear Nighthawk M1?

[lihanbok]

Dear Expert,
I tried to connect TEMS Investigation19 with Netgear Nighthawk M1, but it is not worked. Could you please help me how to connect? If it need usb driver, could you support me?
Thank you so much!
Best Regards,

[lihanbok]

Could you please support me! Thank you so much!
Regards,
Lihanbok.

[carver]

for work with TEMS or QXDM
Netgear Nighthawk M1 MR1100 need enable DIAG port first.
then you can use defaults AC78xSDrivers

[radio_network]

@carver
Friend Is there any way to enable diagnostic port in HiSilicon modem chipset.

[carver]

@carver
Friend Is there any way to enable diagnostic port in HiSilicon modem chipset.

I recently did it for my old E3276s-500, photo of board here
https://www.4shared.com/photo/OH3gZqSZce/huawei_E3276s-500_1.html

my the firmware was very old, so I found a new one.
also, you need necessarily a regular firmware, Hilink firmware doesn't fit

then use AT command for check current port state:

AT^SETPORT?
^SETPORT:FF;10,3,12

check avaible options

AT^SETPORT=?
^SETPORT:1: 3G MODEM
^SETPORT:2: 3G PCUI
^SETPORT:3: 3G DIAG
^SETPORT:5: 3G GPS
^SETPORT:A: BLUE TOOTH
^SETPORT:16: NCM
^SETPORT:A1: CDROM
^SETPORT:A2: SD
^SETPORT:10: 4G MODEM
^SETPORT:12: 4G PCUI
^SETPORT:13: 4G DIAG
^SETPORT:14: 4G GPS


and just add ports:

AT^SETPORT="FF;10,12,13,14"

of course, you will have other numbers.

On this the ports are enabled, they appear in Device Manager

but as far as I know, after 3G ports enabled,
you need to use Huawei Huut,
and load in a modem - a *.hluf license,
for the work of the Huawei software, or other software.

in theory, these *.hluf files give out huawei,
but as always there are other way.

[carver]

2radio_network

I also have a question.

I was asked a question today, to which I have no answer.
as the program is named, for working with the diagnostic port,
on MTK CDMA processors.
I need an similar QXDM for MTK CDMA.

[lihanbok]

Dear Carver,
Could you please tell me how to enable DIAG Port?
Thank you so much!
Best Regards,
Lihanbok.

for work with TEMS or QXDM
Netgear Nighthawk M1 MR1100 need enable DIAG port first.
then you can use defaults AC78xSDrivers

[carver]

2 lihanbok
Only I know who to contact locally in .vn or .ua

[carver]

anybody can share screenshot of Netgear Nighthawk M1 in the TEMS or NEMO.

I don't really understand what I am writing below ))

but I need screenshot with Nighthawk M1 for
- Band locks functions
- cell lock functions
- RAT locks and
- Layer 3 messages

thanks.

[loihut]

For my know, Netgear MR1100 only have RAT Lock, haven't Band lock and Cell Lock.

41738


anybody can share screenshot of Netgear Nighthawk M1 in the TEMS or NEMO.

I don't really understand what I am writing below ))

but I need screenshot with Nighthawk M1 for
- Band locks functions
- cell lock functions
- RAT locks and
- Layer 3 messages

thanks.