Significance of HS-PDSCH MPO Constant

[techfolkcmr]

Hi experts,

Can someone please explain briefly about MPO constant and its optimal value. In our RNC it is set as 2.5db but nemo shows 8.5db during drive.Is there

any parameter in NodeB regarding MPO Constant.Thanks in advance

[erastus]

This parameter indicates the assumed HS-PDSCH power offset relative to the PCPICH power that is used for CQI measurement. For our vendor (ZTE), the default value is 8dB.
However, its dependent on the quality of service and the system capacity.
It's defined on the cell level in steps of 0.5dB.

Hope this answers your question.

NB. Feel free to add on my reputations!

[agenov]

i guess what u see in the Nemo is MPO value. MPOc is part of the calculation for MPO.

[februaryku]

Hi.... As I know that calculation of MPO is different which other vendor.
Huawei :
Measurement power offset is used by UE to obtain total received HS-PDSCH power
Measure Power Offset = Max(-6, Min(13,CellMaxPower - PcpichPower - Measure Power OffsetConstant)

37854

[sabila]

so if we set MPO higher probability CQI more higher and throughput better or what?

[electron]

so if we set MPO higher probability CQI more higher and throughput better or what?

Hi Sabila,

It will shift reported CQI to higher range and higher level modulation scheme usage slightly increases but not essentially increases HS Throughput in practical manner.


Cheers

[kaya_rav]

Pls share process to change in ZTE netnumen.

[kaya_rav]

This parameter indicates the assumed HS-PDSCH power offset relative to the PCPICH power that is used for CQI measurement. For our vendor (ZTE), the default value is 8dB.
However, its dependent on the quality of service and the system capacity.
It's defined on the cell level in steps of 0.5dB.

Hope this answers your question.

NB. Feel free to add on my reputations!


Hi,
In ZTE system pls share process to optimize this param.

thanks in advance.

Ravi

[plannerguy]

Hi

do we have similar MPO values in NSN system?

Rgds
Plannerguy

[Gauiver]

Hi,

MPO stands for measured power offset. You must be aware that scheduling, modulation schemes etc are dependent upon CQI (and there is no explicit description how CQI shall be calculated in any standard), but CQI shall be a function of receiver capability, multipath environment, interference and BTS power capability. The MPO constants adds an offset in the computation of CQI, so if you are using an unreasonable value of MPO, it may impact CQI computation resulting in some crazy values and impacting scheduling, power and code assignment.

And remember impact on CQI of MPO constant may be different in different vendors, as the CQI computation methodology might be different.

Gauiver

[marcengo]

1: In NSN the value is fixed. From what I understand it is not modifiable, unless you are a inside person with access to restricted parameters.

2: The MPO will be used to calculate the reported CQI. On both sides, UE and NodeB, it is not standardized, thus, people do whatever they want. People already said what it means, but in a more direct point, changing the MPO will shift the CQI curve to left of right, depending if you are increasing or reducing the current value.

If the curve is clipped in the higher range, the UE will be reporting too optimistic values, making the NodeB schedule an MCS which the UE is not able to decode with less than 10% BLER. If it is clipped in the lower values, than the opposite logic is applied.

[yassanino]

Hi

do we have similar MPO values in NSN system?

Rgds
Plannerguy

it's Nokia now i guess , he said

[BENRHOUMASALEM]

Hi,

Please to advise about Nokia. How can we change MPO_constant ?

Br,

[justdream]

so experts, recommend not to change MPO !
Any trial reports?