husseinmanaf
2015-03-21, 07:10 AM
Dears
1.
About This Release
© Ascom 2015. All rights reserved.
TEMS is a trademark of Ascom. All other trademarks are the property of their respective holders. Apple, the Apple logo and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
2.
Important Information
2.1.
Disabling Wi-Fi for Mobile Network Testing
Before using state-of-the-art devices such as Sony Xperia Z2 or Samsung S5 models for mobile network data service testing, be sure to turn off Wi-Fi on the device. If Wi-Fi is enabled, the device may run data transfers over Wi-Fi rather than over the mobile network it is camping on (even if a correct APN has been entered).
2.2.
Rohde & Schwarz TSMW Firmware Upgrade
All customers using Rohde & Schwarz TSMW scanners must upgrade to firmware version 2.0.1 to be able to connect the scanners in TEMS Investigation 16.3 and later.
Please refer to www.rohde-schwarz.com/en/firmware/tsmw (http://www.rohde-schwarz.com/en/firmware/tsmw) for R&S firmware download and release notes describing how to upgrade the firmware.
2.3.
VoLTE vs. Data Service Testing with Qualcomm Based Samsung Devices
Qualcomm chipset based Samsung devices with VoLTE capability need to be set up differently depending on what services are to be tested: VoLTE, data, or both. Here are some guidelines:
•
If you are going to test VoLTE only, the device should be either in USB mode DM+MODEM+ADB, or in USB mode MTP+ADB and tethered. Please remember to start the OnDevice IP Sniffing service from TEMS Investigation.
•
If you are going to test data services only, and you need to keep down the size of the logfiles, either disable the DPL log (0x11EB) or set USB mode to RNDIS+DM+MODEM. Be aware that in RNDIS+DM+MODEM mode it is not possible to apply certain control functions such as RAT and band lock. In TEMS Investigation 16.3.1 the DPL log is by default turned off in RNDIS+DM+MODEM mode.
•
If you want to test both VoLTE and data services concurrently, the device must be in USB mode MTP+ADB and tethered if the data testing is to be done over the Ethernet interface. DM+MODEM+ADB will only provide a Dial-Up connection (RAS).
3.
TEMS Investigation 16.3.2
3.1.
New Features
3.1.1.
New Connectable Devices
•
LG G3 D727 (VoLTE-capable device)
1.
About This Release
© Ascom 2015. All rights reserved.
TEMS is a trademark of Ascom. All other trademarks are the property of their respective holders. Apple, the Apple logo and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
2.
Important Information
2.1.
Disabling Wi-Fi for Mobile Network Testing
Before using state-of-the-art devices such as Sony Xperia Z2 or Samsung S5 models for mobile network data service testing, be sure to turn off Wi-Fi on the device. If Wi-Fi is enabled, the device may run data transfers over Wi-Fi rather than over the mobile network it is camping on (even if a correct APN has been entered).
2.2.
Rohde & Schwarz TSMW Firmware Upgrade
All customers using Rohde & Schwarz TSMW scanners must upgrade to firmware version 2.0.1 to be able to connect the scanners in TEMS Investigation 16.3 and later.
Please refer to www.rohde-schwarz.com/en/firmware/tsmw (http://www.rohde-schwarz.com/en/firmware/tsmw) for R&S firmware download and release notes describing how to upgrade the firmware.
2.3.
VoLTE vs. Data Service Testing with Qualcomm Based Samsung Devices
Qualcomm chipset based Samsung devices with VoLTE capability need to be set up differently depending on what services are to be tested: VoLTE, data, or both. Here are some guidelines:
•
If you are going to test VoLTE only, the device should be either in USB mode DM+MODEM+ADB, or in USB mode MTP+ADB and tethered. Please remember to start the OnDevice IP Sniffing service from TEMS Investigation.
•
If you are going to test data services only, and you need to keep down the size of the logfiles, either disable the DPL log (0x11EB) or set USB mode to RNDIS+DM+MODEM. Be aware that in RNDIS+DM+MODEM mode it is not possible to apply certain control functions such as RAT and band lock. In TEMS Investigation 16.3.1 the DPL log is by default turned off in RNDIS+DM+MODEM mode.
•
If you want to test both VoLTE and data services concurrently, the device must be in USB mode MTP+ADB and tethered if the data testing is to be done over the Ethernet interface. DM+MODEM+ADB will only provide a Dial-Up connection (RAS).
3.
TEMS Investigation 16.3.2
3.1.
New Features
3.1.1.
New Connectable Devices
•
LG G3 D727 (VoLTE-capable device)