View Full Version : Moshell problem: MO typename" = "M3uAssociation", "$FRO typename" = "M3UAssociation"
ivanbrij
2013-06-29, 01:25 AM
Dear Experts,
Do you know how to solve the problem when MO typename and FRO typename are differents??
Many thanks,
Ivan
rabatcasa
2013-06-29, 05:42 AM
Hi
What is the issue ? is it that you can not read the MO M3uAssociation and its attributes ?
One solution could be to change the fro table with the sqlc command and one it is done create a new CV, However that this operation is not recommended on a live node
BR/Casa
ivanbrij
2013-06-29, 06:17 AM
Dear,
The problem is than I'm trying to create a M3uAssociation and I got this error
!!!! Processing failure :se.e*******.cello.moframework.FroRequestFailedException TAG :"FroRequestFailed" VARIABLES :"$MO typename" = "M3uAssociation", "$FRO typename" = "M3UAssociation", "$Request type" = "CreateFroReq: UNKNOWN RESULT CODE: 71", "$result" = "71"
Below the Moshell commands used:
RNCSCB03> run /home/e06262/CreateCS1.mos
RNCSCB03>
RNCSCB03> confb+
Confirmation of bl/deb/set/acc commands = disabled
RNCSCB03> gs+
Perform a get before set = enabled
RNCSCB03>
RNCSCB03> cr TransportNetwork=1,Mtp3bSpItu=1,M3uAssociation=MSS_M3UA1
130626-01:12:52 10.53.181.165 9.0g RNC_NODE_MODEL_M_1_150 stopfile=/tmp/17089
Attribute 1 of 3, mtp3bSrsId (moRef:Mtp3bSrs):
Enter mo LDN: Mtp3bSpItu=1,Mtp3bSrs=Mtp3bSrs_MSS_10570 #mtp3bSrsId
Attribute 2 of 3, remoteIpAddress1 (string): 10.19.51.78 #remoteIpAddress1
Attribute 3 of 3, sctpId (moRef:Sctp):
Enter mo LDN: Sctp=SCTP0 #sctpId
Following attributes are optional. Enter attribute value or "d" for default.
Once the MO is created, these attributes cannot be changed (they are restricted).
Attribute 1 of 7, autoStartAssociation (boolean): true #autoStartAssociation
Attribute 2 of 7, dscp (long): 34 #dscp
Attribute 3 of 7, localIpMask (enumRef:HomingState):
Enter one of the following integers: 1:SINGLE_HOMED_1, 2:SINGLE_HOMED_2, 3:MULTI_HOMED: 3 #localIpMask
Attribute 4 of 7, localPortNumber (long): 2905 #localPortNumber
Attribute 5 of 7, remoteIpAddress2 (string): 10.19.50.78 #remoteIpAddress2
Attribute 6 of 7, remotePortNumber (long): 1024 #remotePortNumber
Attribute 7 of 7, role (enumRef:M3uAssociationRole):
Enter one of the following integers: 0:CLIENT, 1:SERVER: 0 #role
!!!! Processing failure :se.e*******.cello.moframework.FroRequestFailedException TAG :"FroRequestFailed" VARIABLES :"$MO typename" = "M3uAssociation", "$FRO typename" = "M3UAssociation", "$Request type" = "CreateFroReq: UNKNOWN RESULT CODE: 71", "$result" = "71"
RNCSCB03> lset TransportNetwork=1,Mtp3bSpItu=1,M3uAssociation=MSS_M3UA1$ congestionAlarmThreshold 50
130626-01:12:53 10.53.181.165 9.0g RNC_NODE_MODEL_M_1_150 stopfile=/tmp/17089
============================================================================================================
Id MO congestionalarmthreshold Result
============================================================================================================
============================================================================================================
Total: 0 MOs attempted, 0 MOs set
RNCSCB03> lset TransportNetwork=1,Mtp3bSpItu=1,M3uAssociation=MSS_M3UA1$ userLabel M3uAssociation_MSS_M3UA1
130626-01:12:53 10.53.181.165 9.0g RNC_NODE_MODEL_M_1_150 stopfile=/tmp/17089
============================================================================================================
Id MO userlabel Result
============================================================================================================
============================================================================================================
Total: 0 MOs attempted, 0 MOs set
How to solve it??
Thanks in advance,
JB
rabatcasa
2013-07-01, 08:28 AM
One reason for the fault is that the dscp value you are setting is not valid :
is there any other M3uAssociation using the same Sctp=SCTP0 ? , if yes then the dscp used for that MO should be also used for the MO M3uAssociation=MSS_M3UA1 that you are trying to create.
The reason is that dscp value is common for all M3UA association using the same SCTP endpoint.
if that does not help, can you get the te log read logs from the node ?
ivanbrij
2013-07-01, 03:18 PM
Thanks Casa,
There are more M3UA using the same SCTP and local port number. I'll try to delete all, then create all.
How to get the logs in case of continue the problem?
BR,
Ivan
rabatcasa
2013-07-02, 06:16 AM
Hi
you can start with $te log read command from the central mp and if you are using moshell >lh mp te log read
Br/Casa
vBulletin® v4.2.5, Copyright ©2000-2024, Jelsoft Enterprises Ltd.