Latest TEMS & Qualcomm Activation

[Optim_z]

Hi All!
How to Active "Some commercial Qualcomm chipset derived phones and data cards may not have diagnostics reporting enabled by default" without contact E******* Support ?

Refer to:
http://www.e*******.com/solutions/tems/support/investigation/sup_ti_swhw_9.0.shtml

Some commercial Qualcomm chipset derived phones and data cards may not have diagnostics reporting enabled by default, and E******* is not at liberty to distribute information on how to enable this function. Customers desiring to use such devices with TEMS Investigation therefore need to contact the relevant supplier or operator in each case. These phones are marked with * in the table below.

[sumon]

which equipment model you wish to activate..?

[hua1687]

还是比较容易的,不很难

[Optim_z]

Original posted by hua1687 at 2008-9-16 10:53 http://www.5inetop.cn/images/common/back.gif (http://www.5inetop.cn/redirect.php?goto=findpost&pid=24678&ptid=1487)
还是比较容易的,不很难

How to Active I`ts ?
you say "It is quite easy, not difficult"
Please share the info!

[ Last edited by Optim_z at 2008-9-16 12:13 ]

[parto_tegal]

Hi All
So far that i have tested, Samsung SGH-Z560 and SGH-Z720 Phones are connectable with TEMS Investigation and can perform good measurement without any need of a special firmware. As well as almost all (but not all) Samsung CDMA phones, as they are an Qualcomm based phones. Also ******** CDMA Phones as V3m, V3c, W362 etc.... It's nice to try, but I think E******* put no warranty on this as we can buy it freely from the open market.
Regards
parto_tegal

[miro]

nice tek talk

[bikplaboi]

Hi Parto-tegal,

Will a Samsung SGH-Z750 as be able to connect to TEMS Investigation with any special firmware loaded?

All I have to do is find the correct phone drivers and thats it?


Please confirm???



THANKS,,,





Hi All
So far that i have tested, Samsung SGH-Z560 and SGH-Z720 Phones are connectable with TEMS Investigation and can perform good measurement without any need of a special firmware. As well as almost all (but not all) Samsung CDMA phones, as they are an Qualcomm based phones. Also ******** CDMA Phones as V3m, V3c, W362 etc.... It's nice to try, but I think E******* put no warranty on this as we can buy it freely from the open market.
Regards
parto_tegal

[redernesto]

Hi Parto-tegal,

Will a Samsung SGH-Z750 as be able to connect to TEMS Investigation with any special firmware loaded?

All I have to do is find the correct phone drivers and thats it?


Please confirm???



THANKS,,,

Yes you can!

i have a Samsung SGH-G400L and it works nice, you just have to download the Qualcomm Drivers

[vibs75]

Kyocera KX2 connects easily , there is no requirement for special firmware, I have tested it, and kyocera is supposed to be good phone for measurement and goos sensitivity.

vibs

[qqhuang]

Will a phone based qualcomm MSM7200 as be able to connect to TEMS Investigation with any special firmware loaded?

[mayank_shah]

To connect with Tems is it required to install any special Software in Phone or just commercial phone need to connect with Tems?

BR//

[jhakim]

To connect with Tems is it required to install any special Software in Phone or just commercial phone need to connect with Tems?

BR//

Hi,

In Qualcom shipset based phones no need to flash ur phone with special firmware, you need only to activate the diagnostic port via AT commands.

Regards,

[wolverine]

See this post... http://www.finetopix.com/showthread.php?t=4199 regarding activating the diagnostic interface for Samsung and Huawei based UEs that use Qualcomm chipsets.

[tomcatsniper]

I confirm that my Huawei E618 Data Card is working with TEMS Inv 8.0.3 with normal drivers from CD that came with the card. I just plugged in the card and open Inv 8. I made a refresh in Ctrl & Config and the card was automaticaly detected. Pressed connect all and working. :)

[adfree]

I can confirm. That Samsung needs to set mandatory Diag Port via some Codes. I see this often with request for BitPim fileaccess.

Z630 for example:

*#3695147*#
Pass on Internals:
*#1456380*#

USB Driver
Now you can select Haje Soft
or
Qualcomm USB

Best Regards

[jiubuwenni]

i want to konw how ,too

[bikplaboi]

Hi All,

Can someone share the various AT commands that will be needed to activate diagnostic ports for various Samsung models (say something like a database) for those people who other models of Samsung phones.

Or is the command more or less the same for phone models.




Thanks,,,,:D







Hi,

In Qualcom shipset based phones no need to flash ur phone with special firmware, you need only to activate the diagnostic port via AT commands.

Regards,

[davidbrayan]

i tried with SAMSUNG SGH-M620
the command used was AT$SUSBC=1 as described in the above mentioned post.
it did something but gave error halfway.
due to which although the modem and serial port which were visible earlier , disappeared but no sign of TRACE port was there.
SAME with ******** V3
only a samsung usb device stays in USB devices after the command. and ******** usb device incase of ******** V3.
SAMSUNG gave some commands when i hit help for advance commands in which a command to switch serial port to tracer port is

AT*TRACE

but gave error with samsung SGH-M620 , this phone is not listed but i tried since its a QUALCOMM MSM6500 chipset based phone and was readily with me.
can somebody explain if i m wrong somewhere?

BR
db

[davidbrayan]

the text captured for SAMSUNG SGH-M620 is as below

ATE1
OK
AT$
AT :
A/ : Repeat last command line
AT? :
AT$ : Help on basic commmands
AT+$ : Help on extended commands
ATD$ : Help on dial command
ATS$ : Help on S Registers
ATA : Answer an Incoming Call
ATDs : Dial a Number
ATEn : Select Modem Command Character Echo
ATHn : Hook Control
ATIn : Request Identification Information
ATLn : Set Monitor Speaker Loudness
ATMn : Set Monitor Speaker Mode
ATOn : Return to Online State
ATP : Select Pulse Dialing
ATQn : Select Result Code Suppression
ATT : Select Tone Dialing
ATVn : Select Result Code Format
ATXn : Select Call Progress Result Code Set
ATZn : Recall Stored Profile
AT&Cn: Select Data Carrier Detect (DCD) Option - Circuit 109
AT&Dn: Select Data Terminal Ready (DTR) Option - Circuit 108
AT&Fn: Set to Factory-Defined Configuration
AT&V: View Active Configuration
AT&Wn: Store Parameters to Given Set
AT&Yn: Select Parameter Set as Powerup Option
AT&Tn: Self-Test Options
AT\Qn: Select Serial Port Flow Control
AT*RAF: switch to RAF mode
AT*TRACE: switch serial port to tracer
AT+GMI: Request Manufacturer Identification
AT+GMM: Request Model Identification
AT+GMR: Request Revision Number

OK
AT*TRACE
ERROR
AT$SUSBC=1
AT :
A/ : Repeat last command line
AT? :
AT$ : Help on basic commmands
AT+$ : Help on extended commands
ATD$ : Help on dial command
ATS$ : Help on S Registers
ATA : Answer an Incoming Call
ATDs : Dial a Number
ATEn : Select Modem Command Character Echo
ATHn : Hook Control
ATIn : Request Identification Information
ATLn : Set Monitor Speaker Loudness
ATMn : Set Monitor Speaker Mode
ATOn : Return to Online State
ATP : Select Pulse Dialing
ATQn : Select Result Code Suppression
ATT : Select Tone Dialing
ATVn : Select Result Code Format
ATXn : Select Call Progress Result Code Set
ATZn : Recall Stored Profile
AT&Cn: Select Data Carrier Detect (DCD) Option - Circuit 109
AT&Dn: Select Data Terminal Ready (DTR) Option - Circuit 108
AT&Fn: Set to Factory-Defined Configuration
AT&V: View Active Configuration
AT&Wn: Store Parameters to Given Set
AT&Yn: Select Parameter Set as Powerup Option
AT&Tn: Self-Test Options
AT\Qn: Select Serial Port Flow Control
AT*RAF: switch to RAF mode
AT*TRACE: switch serial port to tracer
AT+GMI: Request Manufacturer Identification
AT+GMM: Request Model Identification
AT+GMR: Request Revision Number

ERROR
AT$SUSBC=0
AT :
A/ : Repeat last command line
AT? :
AT$ : Help on basic commmands
AT+$ : Help on extended commands
ATD$ : Help on dial command
ATS$ : Help on S Registers
ATA : Answer an Incoming Call
ATDs : Dial a Number
ATEn : Select Modem Command Character Echo
ATHn : Hook Control
ATIn : Request Identification Information
ATLn : Set Monitor Speaker Loudness
ATMn : Set Monitor Speaker Mode
ATOn : Return to Online State
ATP : Select Pulse Dialing
ATQn : Select Result Code Suppression
ATT : Select Tone Dialing
ATVn : Select Result Code Format
ATXn : Select Call Progress Result Code Set
ATZn : Recall Stored Profile
AT&Cn: Select Data Carrier Detect (DCD) Option - Circuit 109
AT&Dn: Select Data Terminal Ready (DTR) Option - Circuit 108
AT&Fn: Set to Factory-Defined Configuration
AT&V: View Active Configuration
AT&Wn: Store Parameters to Given Set
AT&Yn: Select Parameter Set as Powerup Option
AT&Tn: Self-Test Options
AT\Qn: Select Serial Port Flow Control
AT*RAF: switch to RAF mode
AT*TRACE: switch serial port to tracer
AT+GMI: Request Manufacturer Identification
AT+GMM: Request Model Identification
AT+GMR: Request Revision Number

ERROR
AT&V
Serial speed: auto
---------------------S registers-------------------
S00: 0 S02: 43 S03: 13 S04: 10
S05: 8 S06: 2 S07: 1 S08: 2
S10: 1 S12: 50 S23: 0 S37: 2

--------------------- Responses -------------------
Echo: on Quiet: off Verbose: on XValue: 0
------------------ Modem Control ------------------
Handshaking: hw
DTRcontrol: disconnect DCDcontrol: passage
Modem class: 0 Overspeed: on
------------------ Bearer Service -----------------
???asynchronous non-transparent

OK

[wolverine]

i tried with SAMSUNG SGH-M620
the command used was AT$SUSBC=1 as described in the above mentioned post.
it did something but gave error halfway.
due to which although the modem and serial port which were visible earlier , disappeared but no sign of TRACE port was there.
SAME with ******** V3
only a samsung usb device stays in USB devices after the command. and ******** usb device incase of ******** V3.
SAMSUNG gave some commands when i hit help for advance commands in which a command to switch serial port to tracer port is

AT*TRACE

but gave error with samsung SGH-M620 , this phone is not listed but i tried since its a QUALCOMM MSM6500 chipset based phone and was readily with me.
can somebody explain if i m wrong somewhere?

BR
db

Hi,

The command AT$SUSBC=1 is Samsung proprietary and will only work with Samsung UEs. Now it might be because the phone you describe is quite old, it doesn't support this command.

As an alternative solution, try this..

Older Sasmung phones have a test mode that you can access by typing *#123580#

If it works, go to menu item 9, then 6 and then pick Qualcomm USB.

This accomplishes the same thing as the AT command in the original post. If you play around with the test mode you can see some more interesting info like lac, rac, frequencies etc.

[mayank_shah]

what is command if we want to back in Samsung mode?

BR//

[davidbrayan]

what is command if we want to back in Samsung mode?

BR//
to go back to samsung mode the command is

AT$SUSBC=0

but the thing here is ,

at first to switch to trace port we use the modem port which is visible in samsung mode.
but after execution of the command
AT$SUSBC=1
the modem port and the serial port disappears
and the hyperterminal cant connect to the ports previously ment for samsung modem

that problem i faced.
but a workaround is.
i connected the phone with bluetooth connection.
via bluetooth modem i connectd hyperterminal and executed
AT$SUSBC=0
and the samsung mode activated.
so bluetooth modem is always there to help you out in any mode.

BR
db

[davidbrayan]

other commands for samsung m620
OK
AT+$
AT+CGMI,+GMI: Request manufacturer id
AT+CGMM,+GMM: Request model id
AT+CGMR,+GMR: Request revision id
AT+CGSN,+GSN: Request IMEI id
AT+CIMI : Request IMSI
AT+CSTA : Select type of address
AT+CHUP : Hangup call
AT+CBST : Select bearer service type
AT+CRLP : Select radio link protocol
AT+CRC : Select cellular result codes
AT+CREG : Network registration
AT+CCLK : Set real time clock
AT+CLIP : Set calling line id presentation
AT+CLIR : Set calling line id restriction
AT+COLP : Set connected line id
AT+CCWA : Set call waiting supplementary service
AT+CHLD : Call hold and multiparty
AT+CLCC : List Current Calls
AT+CPAS : Request phone activity status
AT+CPIN : Set pin code
AT+CBC : Requenst battery charge info
AT+CCLK : Clock
AT+CLVL : Set loudspeaker volume level
AT+CMEE : Set mobile equipment error
AT+GMI : Request manufacturer identification
AT+GMM : Request model identification
AT+GMR : Request revision identification
AT+GSN : Request Product Serial Number Identification
AT+FCLASS: Request or set fax class
AT+FRH : Receive HDLC frame
AT+FRM : Receive fax data
AT+FRS : Receive silence
AT+FTH : Transmit HDLC frame
AT+FTM : Transmit fax data
AT+FTS : Transmit silence
AT+FAE : Select fax auto answer mode
AT+CGDCONT: Define a PDP context
AT+CGQREQ: Define requested QoS
AT+CGQMIN: Define minimum QoS
AT+CGACT: Activate a PDP context
AT+CGPADDR: Show a PDP address
AT+CGMSACT: switch on/off the MS
AT+CGATT: Attach/Detached GPRS services
AT+FXTLLI: Asssign a TLLI to ??
AT+CGCONF: configuration command for GPRS services
AT+CGDSCONT: Define a secondary PDP context
AT+CGTFT: Define a Pkt Filter for Traffic Flow Template
AT+CGEQREQ: Define requested extended QoS
AT+CGEQMIN: Define minimum extended QoS
AT+CGEQNEG: Show negociated extended QoS
AT+CGCMOD: Modify a PDP context
AT+CGERDATA: Send an unfragmented PDU to the network
AT+CSMS : Select message service
AT+CPMS : Preferred message storage
AT+CMGF : Message format
AT+CSCA : Service center address
AT+CSMP : Set text mode parameters
AT+CSDH : Show text mode parameters
AT+CSCB : Select cell broadcast message types
AT+CSAS : Save settings
AT+CRES : Restore settings
AT+CNMI : New message indications to TE
AT+CMGL : List messages
AT+CMGR : Read message
AT+CMGS : Send message
AT+CMSS : Send message from storage
AT+CMGW : Write message to memory
AT+CMGD : Delete message

OK

[davidbrayan]

the code *#123580# is not working, and the phone i am working with is not that old

http://www.gsmarena.com/samsung_m620-2360.php

released july 2008

so any other modifications or commands??

BR
db

[wolverine]

Hi David,

When you type at$susbc=1, you are de-activating the samsung modem port (that you are using to connect via hyperterminal) so it is normal that you cannot communicate to the phone anymore.

However, if you unplug the phone and re-plug it in the laptop, you should get a Qualcomm modem (with a different port number assigned by the OS) activated. If you have never connected a Qualcomm modem to your laptop you should also get the Found New Hardware Wizzard appearing asking for drivers.

Have you tried this? If so, what is the behaviour when you re-plug the phone after issuing the at$susbc=1 command?

Are there any modems available in the Device Manager under "Modems"?

[davidbrayan]

attaced the screenshot
get nothing on serial as well as modem.

all i get is a samsung usb device.

and can you tell me what is this
AT*TRACE
command is for

BR
db


Hi David,

When you type at$susbc=1, you are de-activating the samsung modem port (that you are using to connect via hyperterminal) so it is normal that you cannot communicate to the phone anymore.

However, if you unplug the phone and re-plug it in the laptop, you should get a Qualcomm modem (with a different port number assigned by the OS) activated. If you have never connected a Qualcomm modem to your laptop you should also get the Found New Hardware Wizzard appearing asking for drivers.

Have you tried this? If so, what is the behaviour when you re-plug the phone after issuing the at$susbc=1 command?

Are there any modems available in the Device Manager under "Modems"?

[wolverine]

I had a look at the phone specs for the M620 and it seems it only supports 2G. As far as I know, Samsung only use Qualcomm chipsets in their dual mode UEs (2G & 3G) which would explain why no Qualcomm ports get activated.

Do you have a dual mode Samsung UE you could try with?

I am afraid I don't know what the AT*TRACE command does..

[davidbrayan]

thanx
now me too think so

http://developer.sprint.com/view_devices.do?device=78785

its different

SAMSUNG SGH-M620 is 2G GSM
SAMSUNG SPH-M620 is 3G CDMA

BR
db

[esteaan]

Hi all,

I've got a LG MU500, which suposed to be compatible with TEMS investigation 8.0.4 . When I plug the handset into laptop, TEMS does recognize it, and even connect to the mobile, but I'm unable to se any statistcs, channel nor any information.

Does anybody have idea how to fix it?

many thanks

[bikplaboi]

Hi redernesto,

I have Samsung SGH-J750 and would like to connect it to TEMS Investigation 8.0.3 is this possible?? and what do I need to do to make the connection???

Could you give step by step instructions on what is required to successfully connect the J750 to TEMS.


Thanks,,,,





Yes you can!

i have a Samsung SGH-G400L and it works nice, you just have to download the Qualcomm Drivers

[user1234]

Is there anyone who's tried Samsung z560 with the command AT$SUSBC=1
?
Is it OK to use with TEMS for both 2G and 3G network?

[mayank_shah]

I am working on it and once i will analyse on Z-560 i will post results on this forum

Right now i am able to connect in Tems 8 and 9 and showing Rx levels, ARFCN but not showing SQI and CI

Mayank

[bikplaboi]

Hi All,

Please could someone give the command for activating measurement feature with the SGH-U900?????

Also confirm if the SGH-Z170 can also be connected to TEMS Investigation???

Also could you confirm if the following Samsung phone models are able to connect to TEMS Investigation 8.0.3

SGH-Z170
SGH-U800
SGH-U100
SGH-D880
SGH-F400
SGH-900i

Any help with this will be much appreciated I will add to you thanks and reputation if the information is reliable and useful



Thanks,,,:D

BIkplaboi











I am working on it and once i will analyse on Z-560 i will post results on this forum

Right now i am able to connect in Tems 8 and 9 and showing Rx levels, ARFCN but not showing SQI and CI

Mayank

[mayank_shah]

samsung Z560 works fine but it is showing CI and all values in dedicated mode.

Mayank

[user1234]

Thanks Mayank and everyone for this topix
I'll get z560 for my pocket.

For other models of Samsung is there any way to confirm it's OK for TEMS?

1. Information from Samsung about Qualcomm integrated with the phones?
2. Get one and try with TEMS and the activation AT command
3. Should we have a list of TEMS working SS mobile up-to-date?

Cheer
:)

[user1234]

We could enable "Test mode" in SamSung (z560 tested) by having codes entered as below
1st *#0011#
2nd *#9999*0#
3rd *#123580#

We could disable "Test mode" with End call button

Deatail of the 3rd option: there are a LOT of options in there, what we're looking for. Diving into with up/down navigation

1 Debug Screen
2 MM information
3 RR information
4 GSM Neighbour Cell
5 GPRS Information
6 SIM Information
7 Handover, Call log
8 Phone Control
9 Antenna Test (Setup/View)

Hit # again and you get the next page of menu:

1 Debug Screen
2 Version Information
3 RF Test
4 UMTS rf nv
5 Read gsm rf nv
6 Write gsm rf nv
7 Base Band
8 Audio
9 Common

Anyone has manual for Samsung test mode? Please upload


Activate and Deactivate Qualcomm mode without using Hyperterminal
1. *#123580#
2. [9] Common
3. [6] USB Configuration
4. [1] Samsung USB / [2] Qualcomm USB

[PaleNxtTel]

I try to connect LG KG-800 Chocolate (2G) mobile to TEMS (Actually I'm trying to connect and test any handset I can get :D) and when I run the modem mode from the handset TEMS automatically detect the DC.

Is there any way to detect the MS by using this model ??
I think that LG handset using Qualcomm chipset.
Does TEMS support LG U8150 U900 KU950 as NEMO ??

[redernesto]

Hi redernesto,

I have Samsung SGH-J750 and would like to connect it to TEMS Investigation 8.0.3 is this possible?? and what do I need to do to make the connection???

Could you give step by step instructions on what is required to successfully connect the J750 to TEMS.


Thanks,,,,

Sorry...kind of late but...

First: Check your Software License, Hasp Key must be licensed to connect that Chipset, my qualcom chipset is MSM7200 so i have that license, on Key reader utilitie you can see that as QUALCOMM C License.

After confirm that you can try with the code: *#0523# and press # 4 times.

Then follow the steps described by User1234 and activate Qualcomm USB

Then Connect the phone and install the drivers(previusly downloaded)

After that TEMS will recognize your phone inmediatly.

BR

[RFviewer]

Very useful info.
Thanks a lot!

[crisnspro]

Sorry...kind of late but...

First: Check your Software License, Hasp Key must be licensed to connect that Chipset, my qualcom chipset is MSM7200 so i have that license, on Key reader utilitie you can see that as QUALCOMM C License.

After confirm that you can try with the code: *#0523# and press # 4 times.

Then follow the steps described by User1234 and activate Qualcomm USB

Then Connect the phone and install the drivers(previusly downloaded)

After that TEMS will recognize your phone inmediatly.

BR

recognized immediatly as "E******* W25" by TEMS 10.0? hehe

[mayank_shah]

Can Anybody tell weather Spice S950 will connect or nor?

[regetdeluxe]

Very useful information. Thanks a lot!

[petro]

Yes, great post!

[fellucia811]

Then, the bottom line - what's the best samsung for this purpose?

[vlgiang2308]

I've got a u400 (ubiquam), which suposed to be compatible with TEMS investigation 8.0.3 . It connected to my laptop via the Qualcomm cable and the laptop recognize it (com4). But i can not connect my phone to Tems!
Why? And how can i fix it?
Please help me?

[sonerss]

Hi

I tried to connect Samsung U900 mobile with Tems9.1 phone but I couldnt It said "No Licence"

I tried to connect Tems Hasp 9.1 dongle and my dongle can perform Qualcomm UMTS C mobiles.

http://www.finetopix.com/showthread.php?p=62065#post62065

http://www.finetopix.com/picture.php?albumid=25&pictureid=24

http://www.finetopix.com/picture.php?albumid=25&pictureid=22

http://www.finetopix.com/picture.php?albumid=25&pictureid=23


How can I connect U900 without any errors?



Sorry...kind of late but...

First: Check your Software License, Hasp Key must be licensed to connect that Chipset, my qualcom chipset is MSM7200 so i have that license, on Key reader utilitie you can see that as QUALCOMM C License.

After confirm that you can try with the code: *#0523# and press # 4 times.

Then follow the steps described by User1234 and activate Qualcomm USB

Then Connect the phone and install the drivers(previusly downloaded)

After that TEMS will recognize your phone inmediatly.

BR

[vibs75]

Hi all,
Can any body tell the activation of CDMA, kyocera kx444, as i am not able to connect to TEMS8.03.
Also I couldnot connect the EVDO Rev A, kindly tell if some body has tried with these phones.

regards
Vibhas

[ajent]

Yes, a lot of qualcomm based phone have diag port , sometimes enabled by defaut sometimes not, i have an e*******W25 router equipated with msm6280 sierra wireless card inside, linux is running inside, a tool bridge Diag serial port > to ip serial (serial over tcp/ip), Tems connect on it by the network (it use network gateway ip W25).

But i have a question, someone is able to lock on Base station ?
Any nvitems or something ?

it could be useful.

Thanks for your experiences.

[redernesto]

Maybe that phone isnt a MSM7200 chipset.

[sonerss]

hi redernesto

Are only the MSM7200 chipset phones connecting the TEMS?


Maybe that phone isnt a MSM7200 chipset.

[desi_larka]

hi

yes you can lock a Qualcomm phone ot a nodeb / scrmabling code by setting the registers 2524 & 3525 through QxDM





Yes, a lot of qualcomm based phone have diag port , sometimes enabled by defaut sometimes not, i have an e*******W25 router equipated with msm6280 sierra wireless card inside, linux is running inside, a tool bridge Diag serial port > to ip serial (serial over tcp/ip), Tems connect on it by the network (it use network gateway ip W25).

But i have a question, someone is able to lock on Base station ?
Any nvitems or something ?

it could be useful.

Thanks for your experiences.

[datmast]

I saw this USB MODEM 3,5G:
Chipset Qualcomm MSM6280
HSDPA/UMTS 2100MHz 7,2Mbps
EDGE/GPRS/GSM/850/900/1800/1900MHz

http://www.phucanh.vn/Thumbnail.ashx/0/180/0/6261D287EDB840E78530B1F31E91CED8/3G_HSDPA_72Mbps-1249542010.jpg

can this use with TEMS/NEMO or not?
thanks

[leekyo]

what is it?it can use tems?

[kaka.enine]

Dear Colleagues..
wanna asking a little case..
I use TEMS 9.0 and try for fun connected it with CDMA phone bundling by local operator, it's working at 1900 Mhz.
After install phone driver, and set the TEMS to Qualcom chipset, and IT CAN be CONNECTED to TEMS software..!! :eek:
At glance, parameter which i need to collect can be appeared, BUT then PROBLEM comes.. :L
The phone can't response when try to execute calling from TEMS, but no problem when i insert manually from the handphone.

All respect to all master here who experianced with TEMS software and CDMA phones,,
a little question from me..
how it can be??
Do you have any suggest what can i do to make it work properly..??
Thanks before.. :)

for additonal information
- I use Haier C700 Handphone
- CDMA handphone which working at 1900 Mhz
- Handphone and can be used to external modem for CDMA 2000 1x technology

[crisnspro]

Dear Colleagues..
wanna asking a little case..
I use TEMS 9.0 and try for fun connected it with CDMA phone bundling by local operator, it's working at 1900 Mhz.
After install phone driver, and set the TEMS to Qualcom chipset, and IT CAN be CONNECTED to TEMS software..!! :eek:
At glance, parameter which i need to collect can be appeared, BUT then PROBLEM comes.. :L
The phone can't response when try to execute calling from TEMS, but no problem when i insert manually from the handphone.

All respect to all master here who experianced with TEMS software and CDMA phones,,
a little question from me..
how it can be??
Do you have any suggest what can i do to make it work properly..??
Thanks before.. :)

for additonal information
- I use Haier C700 Handphone
- CDMA handphone which working at 1900 Mhz
- Handphone and can be used to external modem for CDMA 2000 1x technology

try to use another phone, such as Anydata.

[crisnspro]

can enable the 2 ports, but no diag message. thanks in advance.

[kaka.enine]

try to use another phone, such as Anydata.

what kind of phone is it??

[minhvt]

I try using some teminal have QualComm chipset, but infomation display just a little.