-
Member
Reputation: 37
Ask Nokia Timing Advance
Hi everyone,
can someone help me about how to generate timing advance report from OSS so that it has minimum range of 550 m (the smallest). I had problem since the report from ND 232 shown only from 1.1 km as the smallest range, while in our network now has site distance about 300m (inner city).
Is there any setup in the BSC needed for this ?
Please help.
Thanks.
-
2010-01-27 03:58 PM
# ADS
Circuit advertisement
-
Member
Reputation: 37
Originally Posted by
cormon
Hi everyone,
can someone help me about how to generate timing advance report from OSS so that it has minimum range of 550 m (the smallest). I had problem since the report from ND 232 shown only from 1.1 km as the smallest range, while in our network now has site distance about 300m (inner city).
Is there any setup in the BSC needed for this ?
Please help.
Thanks.
Anyone help please ........
-
Member
Reputation: 42
Can you send ND 232 to me at my mail id bindastpyes@gmail.com
I will go thru it and make u understand
-
Member
Reputation: 42
Hi,
I have checked my ND 232 and found that in my ND 232 there is .55Km rnage also mentioned.
BSC:BSC09CKN Segment: EBAJAJCHAKAN1 (1)
Distance Share
upper in min max ave
TRX EXT range Freq of range power power power
type (km) (km) reports (%) (dBm) (dBm) (dBm)
------ ---- -------- -------- ------- ------ ------ ------
normal 0 0.55 1765212 93.94 0 30
normal 0 1.10 45467 2.42 16 30
normal 0 2.20 42517 2.26 14 30
normal 0 3.30 12835 0.68 22 30
normal 0 4.40 359 0.02 30 30
normal 0 6.60 321 0.02 30 30
normal 0 8.80 1022 0.05 30 30
normal 0 11.00 2412 0.13 30 30
normal 0 17.60 9036 0.48 30 30
normal 0 34.65 0 0.00 -- -- --
Plz share your ND report here.
-
Member
Reputation: 37
Hi, thank u for your reply.
Here is my report example generated from oss:
Last edited by cormon; 2010-02-01 at 01:41 PM
-
Member
Reputation: 42
Hi,
there is a MML command ZTPI by which you can get the infromation about Timing advance measurment table,
and with command ZTPM can modify the observation details.
You need to run ZTPM to get .55KM in your oss reports.
Hope this helps.
Regards.
-
Hi bro,
Actually i don't have ND reporter, do u know how to do get the timing advance table with MML commands or with Nokia report builder??
Br,
Nabil
Last edited by nabil el haddani; 2010-01-30 at 03:20 AM
Reason: rectify
-
Member
Reputation: 42
Here you go. ZPTI will give you the answer
TPI:MEASUR,TIMING_ADV
/* SELECT EXECUTION DETERMINATION OR
SYSTEM NAME OF OUTPUT DEVICE
EXECUTION DETERMINATION:
; .. COMMAND EXECUTION
N .. NO EXECUTION
SYSTEM NAME OF OUTPUT DEVICE:
1 ... 11 CHARACTERS
DEFAULT IS CURRENT DEFINITION */
TPI:MEASUR,TIMING_ADV:;
BSC3i BSC19JPD 2010-01-29 12:47:45
TYPE: TIMING_ADV
TIMING ADVANCE SUB RANGE 1 : 1
TIMING ADVANCE SUB RANGE 2 : 2
TIMING ADVANCE SUB RANGE 3 : 4
TIMING ADVANCE SUB RANGE 4 : 6
TIMING ADVANCE SUB RANGE 5 : 8
TIMING ADVANCE SUB RANGE 6 : 12
TIMING ADVANCE SUB RANGE 7 : 16
TIMING ADVANCE SUB RANGE 8 : 20
TIMING ADVANCE SUB RANGE 9 : 32
LAST MODIFIED: 2009-12-30 15:41:39
ADMIN. STATE: UNLOCKED
OPER. STATE: ENABLED
MEASUREMENT INTERVAL:
MON 08:00-22:00
TUE 08:00-22:00
WED 08:00-22:00
THU 08:00-22:00
FRI 08:00-22:00
SAT 08:00-22:00
SUN 08:00-22:00
START DATE: 2009-12-30
STOP DATE:
OUTPUT INTERVAL: 00:60
COMMAND EXECUTED
-
Member
Reputation: 37
Thanks a lot bro
I just found the problem based on that ZTPI command, it turn out that it was all set to default.
-
Member
Reputation: 42
Good to know that I could be of any help. If Possible plz add to my reputation.
Bookmarks