Thanks Thanks:  0
Showing results 1 to 6 of 6

Thread: CSFB LTE to GERAN Call setup time (CST) optimization

  1. #1
    Senior Member Reputation: 311
    Join Date
    2009-11-27
    Location
    In the world
    Posts
    310


    1 out of 1 members found this post helpful.

    Default CSFB LTE to GERAN Call setup time (CST) optimization question

    Dear friends,

    I'm optimizing CSFB CST from LTE to GERAN. I deployed CSFB with RIM feature to reduce the time for UE reading 2G SIB after redirection from LTE. But I saw 2 different cases with Sony XZ Premium and Samsung Note 5. Sony XZ Premium has less time to start "CM service request" when compared to Samsung Note 5, it means less CSFB CST. Samsung Note 5 needs to wait for SIB 2 type before starting "CM service request" while Sony XZ did not.

    Based on the standard (3GPP 44.108 3.2.1) MS no need to re-read any message if it has in the E-UTRA RRCConnectionRelease message. It's different with the real test case.

    Could anyone can help me the reason why does the MS read some SIB in 2G before making "CM Service Request" and Why does it have the different procedure on 2 phones.

    Many thanks,


    :Sony XZ Premium CSFB.jpgSamsung Note 5 CSFB.jpg
    Last edited by linhhy; 2018-04-24 at 04:39 PM Reason: correct tiltle

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many
     

  3. #2
    Member Reputation: 238
    Join Date
    2009-01-20
    Posts
    539


    Default Re: CSFB LTE to GERAN Call setup time (CST) optimization question

    Hi

    Some queries

    Is this tested under same cell.?
    Is data session on going ?

    Rgds
    Plannerguy

  4. #3
    Senior Member Reputation: 311
    Join Date
    2009-11-27
    Location
    In the world
    Posts
    310


    Default Re: CSFB LTE to GERAN Call setup time (CST) optimization question

    Quote Originally Posted by plannerguy View Post
    Hi

    Some queries

    Is this tested under same cell.?
    Is data session on going ?

    Rgds
    Plannerguy
    Hi, it comes from the same cell and no data session on going.

  5. #4
    Senior Member Reputation: 311
    Join Date
    2009-11-27
    Location
    In the world
    Posts
    310


    Default Re: CSFB LTE to GERAN Call setup time (CST) optimization question

    I tested a hundred calls and I saw the same procedure on each phone, but the difference between two phones.

    It is clear that Sony device has much less time to start the call when compared to Samsung device which takes more time to wait for SIB 2 before making call setup. Can I cutoff SIB2 for all devices in this step?

    When comparing 2 phones, it’s also made me confusing that Sony device can read SIB 1, 3, 13 in too short time. (it’s less than 2 multi frames while the standard requires around 4 Multi frames).

    Here is a different time for starting call setup in 2G from LTE side between 2 phones at 100 calls:

    Screenshot_1.jpg

  6. #5
    Member Reputation: 38
    Join Date
    2011-05-13
    Posts
    18


    Default Re: CSFB LTE to GERAN Call setup time (CST) optimization question

    Hi linhhy,

    Seems the problm is in 2G part. Noticed that there is an additional authentication phase for the 2nd mobile, which may be due to a mobile class mark issue at BSC level.

    Did you check if there is class mark enquiry sent by BSC ? This leads to a further delay in call setup after CSFB has been triggered.

    if it's the case, then it's not required as UE will report by itself the class mark change ( for Huawei vendor).

    in this case the related parameter should be modified.

    BR.
    Last edited by karimos; 2018-12-21 at 07:18 PM

  7. #6
    Senior Member Reputation: 311
    Join Date
    2009-11-27
    Location
    In the world
    Posts
    310


    Default Re: CSFB LTE to GERAN Call setup time (CST) optimization question

    Quote Originally Posted by karimos View Post
    Hi linhhy,

    Seems the problm is in 2G part. Noticed that there is an additional authentication phase for the 2nd mobile, which may be due to a mobile class mark issue at BSC level.

    Did you check if there is class mark enquiry sent by BSC ? This leads to a further delay in call setup after CSFB has been triggered.

    if it's the case, then it's not required as UE will report by itself the class mark change ( for Huawei vendor).

    in this case the related parameter should be modified.

    BR.
    Hi Karimos,

    The problem here is the process of searching 2G network between different phones.

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •