Thanks Thanks:  3
Showing results 1 to 7 of 7

Thread: intra-f meas in CM

  1. #1
    Member Reputation: 119
    Join Date
    2008-09-18
    Posts
    249


    Default intra-f meas in CM

    Hi dears,

    can anyone tell me hwo to find the threshold for starting intra-freq measurement in connected mode for HW ?

    thx a lot

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Posts
    Many
     

  3. #2
    Member Reputation: 119
    Join Date
    2008-09-18
    Posts
    249


    Default Re: intra-f meas in CM

    this is basic question for huawei experts ! no reply at all

  4. #3
    Member Reputation: 37
    Join Date
    2008-11-13
    Posts
    31


    Default Re: intra-f meas in CM

    the parameter is HoMeasComm.SMeasure. Default value HoMeasComm.SMeasureInd is off.
    I don't know the the threshold applied when SMeasureInd is off, probably it always measure.

  5. Thanks auto_art, omaryousri thanked for this post
  6. #4
    Member Reputation: 34
    Join Date
    2013-01-28
    Posts
    27


    1 out of 1 members found this post helpful.

    Default Re: intra-f meas in CM

    LTE Intra Frequency Measurement

    The UE triggers intra-frequency measurements if the one of the below conditions is fulfilled:

    1. The serving cell fulfils Srxlev < SIntraSearchP or Squal < SIntraSearchQ.
    2. The UE performs intra-frequency measurements regardless of the RX signal level or quality of the serving cell if CELLRESEL.SIntraSearchCfgInd or CELLRESEL.QQualMinCfgInd is set to NOT_CFG

    Points:
    o If CELLRESEL.SIntraSearchCfgInd is set to NOT_CFG, SIntraSearch is not broadcast in SIB3; if CELLRESEL.QQualMinCfgInd is set to NOT_CFG, SIntraSearchP and SIntraSearchQ are not broadcast in SIB3.
    o If neither of SIntraSearchP nor SIntraSearchQ is specified, UE applies the default value (SIntraSearchP = Infinity, SIntraSearchQ = 0, based on 3GPP 36.331).
    o When both SIntraSearch and SIntraSearchP are broadcast in SIB3, the UE takes the value of SIntraSearchP as that for SIntraSearchP.
    SIntraSearch and SIntraSearchP are set by CELLRESEL.SIntraSearch

    Intra-frequency Cell Reselection Criteria
    In all cases, the UE shall reselect the new cell, only if the following conditions are met:

    · The new cell is better ranked than the serving cell during a time interval TreselectionRAT (The cell reselection time for an intra-frequency neighboring cell is broadcast in the SIB3 and set by the CELLRESEL.TreselEutran parameter. The cell reselection time for an inter-frequency neighboring cell is broadcast in the SIB5 and set by the EUTRANINTERNFREQ.EutranReselTime parameter).
    · The UE has camped on the serving cell for more than 1 second.
    Last edited by tanz; 2016-11-14 at 07:45 AM

  7. #5
    VIP Member Reputation: 1787
    Join Date
    2010-04-23
    Location
    Polar Bear
    Posts
    1,047


    Default Re: intra-f meas in CM

    above is for idle mode isn't?


    HoMeasComm SMeasure SMeasure DBS3900 LTE/BTS3900 LTE/BTS3900A LTE/BTS3900L LTE/BTS3900AL LTE MOD HOMEASCOMM
    LST HOMEASCOMM
    Indicates the threshold below which measurements on neighboring cells are started. If the signal quality of the serving cell exceeds this threshold, the UE is not required to perform intra-frequency, inter-frequency, or inter-RAT measurements, leading to reduced power consumption. The value -141 does not take effect, and is reserved for forward compatibility. If this parameter is set to -141, the value -140 is used as the threshold in implementation. NO NO No LBFD-00201801 / TDLBFD-00201801
    LBFD-00201802 / TDLBFD-00201802
    LOFD-001019 / TDLOFD-001019
    LOFD-001020 / TDLOFD-001020
    LOFD-001021
    LOFD-001022 / TDLOFD-001022
    Coverage Based Intra-frequency Handover
    Coverage Based Inter-frequency Handover
    PS Inter-RAT Mobility between E-UTRAN and UTRAN
    PS Inter-RAT Mobility between E-UTRAN and GERAN
    PS Inter-RAT Mobility between E-UTRAN and CDMA2000
    SRVCC to UTRAN
    Interval Type -141~-43 N/A dBm -141~-43 -44 -44
    Last edited by auto_art; 2016-11-14 at 10:37 AM
    Auto_art Default PAS: london
    pl rate threads for their usefulnes
    share & care

  8. #6
    Junior Member Reputation: 11
    Join Date
    2013-01-22
    Posts
    10


    Default Re: intra-f meas in CM

    This procedure is for Cell Reselection in Idle Mode.

    In Connected Mode the UE always measures the Intra-Frequency neighbors and based on the "A3 Event" settings it may trigger Intra-Frequency handover procedure.

  9. Thanks omaryousri thanked for this post
  10. #7
    Member Reputation: 26
    Join Date
    2017-10-16
    Posts
    14


    Default Re: intra-f meas in CM

    dear do you know the name of the Intra Frequency HO counter in Nokia for LTE??

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •