Thanks Thanks:  1
Showing results 1 to 7 of 7

Thread: HiSi UE Agent - problem with UE detection

  1. #1
    Junior Member Reputation: 10
    Join Date
    2014-08-12
    Posts
    3

    Default HiSi UE Agent - problem with UE detection

    Hi,
    I have a problem with HiSi UE Agent. I have Huawei E3276 dongle and I want do connect it with HiSi UE Agent, but HiSi UE Agent has some problems with making contact with UE.
    I tried different versions of HiSi UE Agent: 2.0.1, 2.1.0 and 2.2.0 - this versions does not see UE. Only HiSi UE Agent 3.0.1 sees it but there is a problem with connection - Invalid Authorized.
    What do I need to do to connect UE and HiSi UE Agent?

    BRs,
    Feluch

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Posts
    Many
     

  3. #2
    Member Reputation: 22
    Join Date
    2014-04-16
    Location
    Around the world
    Posts
    21

    Default Re: HiSi UE Agent - problem with UE detection

    which software your are using tems or nemo ? when its connect to tems its show different port then device manager

  4. #3
    Junior Member Reputation: 10
    Join Date
    2014-08-12
    Posts
    3

    Default Re: HiSi UE Agent - problem with UE detection

    Hi,
    I am using XCAL drive test equipment. I cannot check ports in XCAL. XCAL contacts with UEs by HiSI UE Agent.
    When I connect XCAL to UE via HiSI UE Agent, XCAL works OK about 10 seconds and then shows error message that UE does not send any data or information and disconnects from UE.
    I forgot to write about open ports. Huawei E3276 has COM ports opened:
    3G Application Interface,
    3G GPS Interface,
    Application Interface,
    Bluetooth Interface,
    GPS Interface,
    PC UI Interface.
    I checked that HiSI UE Agent connects with Huawei e3276 via GPS Interface
    UE is connected to HiSi UE
    Client is disconnected due to Invalid Authorized status

    Maybe there is some AT command which is needed?

    BRs,
    Feluch
    Last edited by feluch; 2014-08-14 at 03:46 PM

  5. #4
    Member Reputation: 22
    Join Date
    2014-04-16
    Location
    Around the world
    Posts
    21

    Default Re: HiSi UE Agent - problem with UE detection

    wrong port open its shoud open 3 port as i tested with tems and nemo i not try with xcal. i thing its default port you mention there . need to change firmware to change ports

  6. #5
    Junior Member Reputation: 10
    Join Date
    2014-08-12
    Posts
    3

    Default Re: HiSi UE Agent - problem with UE detection

    Hi,
    Which ports should be open?
    I tested few times more my issue and I observed that UE connects with HiSI UE Agent by 3 ports randomly (PC UE, GPS or Application Interface). In every case there is problem with authorization in HiSi UE Agent.
    I can close and open ports by AT Commands without firmware modification.
    Which version of HiSi UE Agent did you test? Which model of UE do you use?

    BRs,
    feluch

  7. #6
    Member Reputation: 22
    Join Date
    2014-04-16
    Location
    Around the world
    Posts
    21

    Default Re: HiSi UE Agent - problem with UE detection

    i use Huewai data card E-3267 SUPPORT 150 Mbps DL.

  8. #7
    Member Reputation: 247
    Join Date
    2009-08-15
    Posts
    243

    Default Re: HiSi UE Agent - problem with UE detection

    HI,feluch!
    can you give you HiSi UE Agent 3.0.1 here.
    we need it very much
    thank you in advance!

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •