-
Member
Reputation: 73
1 out of 1 members found this post helpful.
TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Hi to All,
I hope you are all well. Need help, advice and recommendations.
I have problem in TS SYNC FAULT for several TRX, that I can not solved.
I already encounter and read these thread here in finetopix but still no permanent resolutions.
Situations:
- our network is GSM BSS 08A/ RBS2216 2+2+2 Config/RBS is not cascaded to any RBS
- E1 Tx' is OK and NO SLIP ERROR
- I already performed Blocked/Deblocked of TS and conduct loop-test to BSC and result will be looptest failed
- I checked BSC side on RP and there is no alarm, already switch RP
- I already replaced DRU, TMA and DXU at RBS side, recommissioned.
Please if any one who already encounter these problem and resolutions, NEED HELP.
What else could I do. PLEASE!
Thanks to All
br\\
-
2013-03-02 01:58 PM
# ADS
Circuit advertisement
-
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Check your EDGE configuration, most probably you defined more NUMREQEGPRSBPC than reserved 64K Abis. As a trial disable EDGE on site and you will see problem will be solved and then have appropriated setting it will solve the problem
Originally Posted by
jndomingo
Hi to All,
I hope you are all well. Need help, advice and recommendations.
I have problem in TS SYNC FAULT for several TRX, that I can not solved.
I already encounter and read these thread here in finetopix but still no permanent resolutions.
Situations:
- our network is GSM BSS 08A/ RBS2216 2+2+2 Config/RBS is not cascaded to any RBS
- E1 Tx' is OK and NO SLIP ERROR
- I already performed Blocked/Deblocked of TS and conduct loop-test to BSC and result will be looptest failed
- I checked BSC side on RP and there is no alarm, already switch RP
- I already replaced DRU, TMA and DXU at RBS side, recommissioned.
Please if any one who already encounter these problem and resolutions, NEED HELP.
What else could I do. PLEASE!
Thanks to All
br\\
-
Member
Reputation: 73
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Hi electron,
Thanks for the response. Its good to hear from you.
First: I already give thanks and reputation for your recommendations, thanks again.
=========================================================
the EDGE/GPRS TS for these site as per BPC data,
NUMREQEGPRSBPC: CHGR 0 = 1 , CHGR 1 = 0
CELL CONFIGURATION BPC DATA
CELL
BNI702A
CHGR NUMREQBPC NUMREQEGPRSBPC NUMREQCS3CS4BPC TN7BCCH EACPREF
0SYSDEF 1 0 GPRS
1 8 0 0
END
=============================================================
- How Can I disable the EDGE on site, through BSC side?
- In these particular EDGE/GPRS parameters above, what further recommended setting above.
thanks electron. . .
br
Last edited by jndomingo; 2013-03-02 at 04:24 PM
-
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
As i mentioned as a trial change NUMREQEGPRSBPC=0 for all CHGR for all cells on this site and check the alarm status again if it disappeared it means wrong configuration on EDGE exist
Originally Posted by
jndomingo
Hi electron,
Thanks for the response. Its good to hear from you.
First: I already give thanks and reputation for your recommendations, thanks again.
=========================================================
the EDGE/GPRS TS for these site as per BPC data,
NUMREQEGPRSBPC: CHGR 0 = 1 , CHGR 1 = 0
CELL CONFIGURATION BPC DATA
CELL
BNI702A
CHGR NUMREQBPC NUMREQEGPRSBPC NUMREQCS3CS4BPC TN7BCCH EACPREF
0SYSDEF 1 0 GPRS
1 8 0 0
END
=============================================================
- How Can I disable the EDGE on site, through BSC side?
- In these particular EDGE/GPRS parameters above, what further recommended setting above.
thanks electron. . .
br
-
Member
Reputation: 73
1 out of 1 members found this post helpful.
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Hi electron,
Thanks again for the suggestions, I do really appreciate your help. . .
added: thanks and reputation for your reply
thanks
br//
-
Member
Reputation: 44
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Originally Posted by
jndomingo
Hi electron,
Thanks again for the suggestions, I do really appreciate your help. . .
added: thanks and reputation for your reply
thanks
br//
Dear;
Did the problem fixed, I am facing the same. Pls if yes tell us how...
BR//
-
Member
Reputation: 44
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Have you check RBLT/Device on Abis?
For Abis use TDM or SCM?
-
Member
Reputation: 73
1 out of 1 members found this post helpful.
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Hi electron,
I hope your well. .
=================================================================================================
as a trial, I already replaced the value NUMREQEGPRSBPC=0, for CHGR 0 = 0, CHGR 1 = 0, The alarm TS SYNCFAULT Ceased.
CELL CONFIGURATION BPC DATA
CELL
BNI702C
CHGR NUMREQBPC NUMREQEGPRSBPC NUMREQCS3CS4BPC TN7BCCH EACPREF
0 SYSDEF 0 0 GPRS
1 8 0 0
END
<
==================================================================
But After several hours, The alarm RAISED again. . . .
<rxasp:moty=rxots;
RADIO X-CEIVER ADMINISTRATION
MANAGED OBJECT ALARM SITUATIONS
MO SCGR SC RSITE ALARM SITUATION
RXOTS-82-2-1 NLBNI702 TS SYNC FAULT
RXOTS-82-2-2 NLBNI702 TS SYNC FAULT
END
=================================================================
-Previously Several of the sectors have TS SYNC FAULT ALARM, But when I change NUMREQEGPRSBPC=0 , it reduced to only 1 to 2 TS have occured in some TRX.
br\
-
Member
Reputation: 73
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Hi Mobila179,
Thanks for the reply, The problem recured. see my reply to electron. Im searching final resolution to these problem.
Thanks for concerned, I give you thanks for your response.
If you get the solutions to these alarm, please share. .
Thanks again mobila179
br//
-
Member
Reputation: 38
Re: TS SYNC FAULT ALARM FOR SEVERAL TRX NEED HELP
Is the BSC in which this site is connected use ABIS optimization feature?
Bookmarks