Why Serving cell monitor itself in GSM network.

**lihanbok** · 2013-01-24, 12:50 PM

Hi Expert,
Could you please explain this situation. Why the Serving cell monitor itself in GSM network(dedicated mode)? can it affect the RxQuality of cell or not(picture below). Thank you so much.
Best Regards,
Lihanbok.

**Finetopix** · 2013-01-24 12:50 PM

**magno22** · 2013-01-24, 01:05 PM

i have same problem. If anyone know this issue please help us.

**mobilis** · 2013-01-24, 01:18 PM

Dear gents
This is not a problem and will not affect the Quality , This happen when you add the BCCH of the serving cell in the BA2 list (BCCH allocation list for didecate mode ) so the MS will scan the BCCH it self ,
Hope this Helps you

**lihanbok** · 2013-01-24, 03:43 PM

Hi mobilis,
I think your answer is not correct. I have already check BA2, I didn't add the Serving BCCH. Do you have other answer. Thanks
Regards,
Lihanbok

**rfworld** · 2013-01-24, 03:59 PM

Originally Posted by lihanbok

Hi mobilis,
I think your answer is not correct. I have already check BA2, I didn't add the Serving BCCH. Do you have other answer. Thanks
Regards,
Lihanbok

There are 2 types of RxLev as shown in the picture.
1. RxLev Sub
2. RxLev Full

**mobilis** · 2013-01-24, 06:34 PM

Originally Posted by lihanbok

Hi mobilis,
I think your answer is not correct. I have already check BA2, I didn't add the Serving BCCH. Do you have other answer. Thanks
Regards,
Lihanbok

Hi Lihanbok
This already happen with me in Huwaei BSC32 the BA list was configured Manualy and for ZTE BSC V6 witch is automatically configured ,
Regarding the Quality ,this will not affect the Quality ,
What I need from you ,
1 In which vendor you are working
2 Please to share the Drive test log file with cell file ,in order to confirm

**mobilis** · 2013-01-24, 06:40 PM

Originally Posted by rfworld

There are 2 types of RxLev as shown in the picture.
1. RxLev Sub
2. RxLev Full

Hi rfworld
When the DTX is activated you have to take the value of RxLev Sub else RxLev Full
the 2 value in the Picture are
the first one for the serving cell But With POWER CONTROL that's why it is lower then the Second Value which is for the BCCH Freq (Max output power)

**lihanbok** · 2013-01-25, 02:09 AM

Hi mobilis,
I have already check in BSC6900 and I didn't add BCCH of Serving cell in BA2. I rarely met it before. I agree with you about not affect to Rx Quality. Could you please tell me how to solve it. Thank you.
Regards,
Lihanbok

**alibushehri** · 2013-01-25, 01:27 PM

Hi,

Do you have a Multiband network, like GSM900&DCS1800 ? This feature is mainly designed for BSC, during handover or Assignment on overlaid and underlaid. for the time that the MS is on overlaid like 1800 band the pathloss is less than 900 band and since usually BCCH is on 900 band, by using this feature you can see the difference in pathloss of different layers. So either you should have a parameter to set this difference, or you can let your BSS calculate it on case by case bases

**Ahmed Adel** · 2013-01-27, 05:29 AM

Hi,

that issue is related to the Parameter PWRC, this parameter which include the BCCH power at MRs or Not, if this parameter is set to yes, the BCCH power Should include at the send MRs From MS side.
so you can check this parameter

thanks