Thanks Thanks:  0
Showing results 1 to 6 of 6

Thread: HOw to decrease SDCCH Drops

  1. #1
    Senior Member Reputation: 587
    Join Date
    2010-07-28
    Location
    https://t.me/pump_upp
    Posts
    244


    Default HOw to decrease SDCCH Drops

    Hi guys,

    Can any one give me the guidance how to reduce the SDCCH Drops in the network.

    FYI 2 SDCCH timeslots are enabled for all the cells by default and based on the traffic it differs............

  2. # ADS
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many
     

  3. #2
    Senior Member Reputation: 502
    Join Date
    2008-11-05
    Posts
    1,025


    Default Re: HOw to decrease SDCCH Drops

    Quote Originally Posted by mail2paturi View Post
    Hi guys,

    Can any one give me the guidance how to reduce the SDCCH Drops in the network.

    FYI 2 SDCCH timeslots are enabled for all the cells by default and based on the traffic it differs............
    1- Clean the Frequencies BCCH and TCH .
    2- Put Your SDCCH TS on BCCH Frequency because BCCH is more clean and there is no power control .
    3- Limit the overshooting .
    RF engineer

  4. #3
    Member Reputation: 18
    Join Date
    2010-04-06
    Posts
    50


    Default Re: HOw to decrease SDCCH Drops

    hello,

    first check abnormal sd traffic...

    1. Check handover traffics; if there are excessive HO numbers then load SD Channels. Yu can retune handover parameters and enhance minimum interval of pbgt handovers. This may hold traffic on uncongested cells.

    2. Check CSSR; if less than KPI, may mean that some subscribers cannot move to dedicated mode due to inadequate SD Channels.

    3. Cell maybe overshooting and gets more traffic. You can downtilt or reduce power to decrease traffic for this cell. This also reduce sd traffic. You can reduce cell layer too....

    4 if there is no tch congestion also no half rate, then you can convert one tch timeslot to sd time slot...

    these may cause load sd channels and drop..

    :-)
    Last edited by salmeterol; 2011-06-07 at 04:44 PM

  5. #4
    Member Reputation: 238
    Join Date
    2009-01-20
    Posts
    539


    Default Re: HOw to decrease SDCCH Drops

    Hi

    check over the

    1) Rxlevelmin.

    same is to prevent the MS form acessing the network in low level condition and getting into out of coverage area

    2) Modify with T200 timers

    More flexiblity in Tx and Rx of the channel


    Regards
    Plannerguy

  6. #5
    Member Reputation: 253
    Join Date
    2009-12-31
    Posts
    535


    Default Re: HOw to decrease SDCCH Drops

    Hi,

    Have you checked or collect stats of TCH Measurements (in HUAWEI) shows counters in Mean Number of SDCCHs in interference band 1-5.
    Call Drops Causes which you can create from Task List.

    Regards//

  7. #6
    Senior Member Reputation: 587
    Join Date
    2010-07-28
    Location
    https://t.me/pump_upp
    Posts
    244


    Default Re: HOw to decrease SDCCH Drops

    Thanks for all your suggestions................

    Finally done with some physical optimization in sites which reduced the SDCCH drops and still experimenting things based on ur inputs........

    Thanks for each and every one for guiding me ...........

Bookmarks

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •