-
2G - 3G Cell reselection issue
Hi,
Can anyone please shed some light on what could cause 2G - 3G cell reselection issue. UE in idle mode not able to latch on to particular 3G site from a 2G site.
-
2011-05-27 01:25 PM
# ADS
Circuit advertisement
-
Member
Reputation: 195
Re: 2G - 3G Cell reselection issue
Originally Posted by
fon909
Hi,
Can anyone please shed some light on what could cause 2G - 3G cell reselection issue. UE in idle mode not able to latch on to particular 3G site from a 2G site.
So you're coming from a 2G site going to 3G site? Maybe there's no UMTS/GSM reselection available between sites..Or 3G site was not on-air..
-
Member
Reputation: 54
Re: 2G - 3G Cell reselection issue
from Huawei vendor ,
just add the 3g cell in 2g BA list for cell reselection.
-
Member
Reputation: 42
Re: 2G - 3G Cell reselection issue
What about NSN system? I m facing the same issue in INDIA. We are not able to reselect 2G to 3G .
-
Re: 2G - 3G Cell reselection issue
Hi all
for 2G-3G reselection you have to check the following:
*3G cell is defined as neighbour in 2G side
*3G cell parameters defined in 2G side should be correct (LAC,PSC,RNC)
*may be the threshold or parameters are set wrong check (FDDQmin(dB),FDDQoffset,2G-3G inter-rat enabled switch(sholud be on),Q_search_I(should be always search for 3G ngbr) )
also check if the 3G cell is barred or not
hope it help you
Regards
-
Member
Reputation: 18
Re: 2G - 3G Cell reselection issue
MOD CELLCCUTRANSYS FDD Qmin 3
MOD CELLCCUTRANSYS Qsearch I 7
MOD CELLCCUTRANSYS Qsearch P 7
MOD CELLCCUTRANSYS FDD Q Offset 0
MOD CELLCCUTRANSYS Qsearch C 15
MOD CELLCCUTRANSYS 3G Search PRIO Yes
SET CELLHOBASIC Inter-RAT Out BSC Handover Enable YES
SET CELLHOBASIC Inter-RAT In BSC Handover Enable YES
SET CELLHOBASIC Inter-RAT Cell Reselection Enable YES
You should modify some parameter and declare 3G cell as a neighbor on 2G cell
Best wishes
-
Member
Reputation: 42
Re: 2G - 3G Cell reselection issue
Thx for yr suggestion............
Now 2G-3G cell reselection is successful but i m not able to lauch on 3G most of the time. UE should take Higher Freq ( 3G- 2100 Mhz ) as compair to 2G..So bydefault it should go to 3G if we have 3G coverage.
Wht are the cause for delay in cell reselection for 2G to 3G?
-
Re: 2G - 3G Cell reselection issue
Originally Posted by
ajay_msfather
Thx for yr suggestion............
Now 2G-3G cell reselection is successful but i m not able to lauch on 3G most of the time. UE should take Higher Freq ( 3G- 2100 Mhz ) as compair to 2G..So bydefault it should go to 3G if we have 3G coverage.
Wht are the cause for delay in cell reselection for 2G to 3G?
check QSI,QSC parameter most probably they are not correct
-
Senior Member
Reputation: 386
Re: 2G - 3G Cell reselection issue
For me the problem is only with BB-9520-Storm 2 handset,
It is not moving from 2g to 3G automatically.
Aall other handsets are fine...
Regards
Scorpion-Learning 5G+4G
No Thanks Please ....But few clicks on Reputation always Welcome :-))
-
Member
Reputation: 154
Re: 2G - 3G Cell reselection issue
Hello there,
This 2G - 3G cell reselection issue for smart phones iphone 4 and Blackberry, was noticed in networks where RAN is provided by Huawei and Core is provided by NSN.
My question is this problem reproducable in the test bed?
Would colleagus facing this problem to share the software version of the network elements they are using in their network?
Is NSN core R4 or a higher release?
Regards,
Bookmarks