-
Junior Member
Reputation: 10
congestion in RRC phase (RRC capacity)
Hi all
in GSM system we have the SD channels that transport signalling traffic.
If we have blocks we can take a TS (time slot) dedicated for TCH and define it as new SD.
In this way we can improve accessibility
In UMTS we have RRC connection , but i don't understand when we will have blocks.
If we have only a carrier f1, how many simultaneous attempts are neccessary to have blocks ? how is it possible whe we need to expande the rrc connection capacity ?
thanks
-
2011-04-08 07:37 PM
# ADS
Circuit advertisement
-
Member
Reputation: 218
Re: congestion in RRC phase (RRC capacity)
Originally Posted by
Mr_Piongly
Hi all
in GSM system we have the SD channels that transport signalling traffic.
If we have blocks we can take a TS (time slot) dedicated for TCH and define it as new SD.
In this way we can improve accessibility
In UMTS we have RRC connection , but i don't understand when we will have blocks.
If we have only a carrier f1, how many simultaneous attempts are neccessary to have blocks ? how is it possible whe we need to expande the rrc connection capacity ?
thanks
in RRC it's not count by number the below cause can cause rejection:
- CAC because of UL/DL power
- NO CE availble
- No Iub resource.
- No Code available.
-
Member
Reputation: 228
Re: congestion in RRC phase (RRC capacity)
Dear,
the Capacity in UMTS is related to : Codes , CEs , Downlink Power , RTWP (which is uplink interference = Load of the cell) and Iub Resources .
you can have blocked RRC (Rejected) when you don't have enough resources of at least one of the above mentioned .
first UE sends RRC Connection Request . then if the system has enough resources , it will send RRC Connection Setup (RRC Accepted) .
-
Member
Reputation: 149
Re: congestion in RRC phase (RRC capacity)
for RRC 4 parameter : Code, Power, CE and Iub that's all
-
Member
Reputation: 67
Re: congestion in RRC phase (RRC capacity)
Originally Posted by
riyantoyadi
for RRC 4 parameter : Code, Power, CE and Iub that's all
Does the uplink interference influence on the RRC Connection capacity?
-
Member
Reputation: 218
Re: congestion in RRC phase (RRC capacity)
Originally Posted by
Mctest
Does the uplink interference influence on the RRC Connection capacity?
yes if ul cac is enable for ul power
Last edited by Walid Madih; 2011-04-11 at 04:11 AM
-
Member
Reputation: 19
Re: congestion in RRC phase (RRC capacity)
Originally Posted by
Walid Madih
in RRC it's not count by number the below cause can cause rejection:
- CAC because of UL/DL power
- NO CE availble
- No Iub resource.
- No Code available.
How do we know, RRC blocking due to UL/DL power...?
And 4 of cause...
Anybody can explain it...?
Sorry, newbie..
-
Member
Reputation: 149
Re: congestion in RRC phase (RRC capacity)
Huawei have special counter about that :
VS.RRC.Rej.Power.Cong Failure of requesting for power resources.
VS.RRC.Rej.UL.CE.Cong Failure of requesting for uplink CE resources in a cell.
VS.RRC.Rej.DL.CE.Cong Failure of requesting for downlink CE resources in a cell.
VS.RRC.Rej.Code.Cong Failure of requesting for code resources.
VS.RRC.Rej.ULIUBBandCong RNC admission algorithm rejection due to congestion of the uplink Iub interface bandwidth.
VS.RRC.Rej.DLIUBBandCong RNC admission algorithm rejection due to congestion of the downlink Iub interface bandwidth.
hope it usefull
-
Member
Reputation: 129
Re: congestion in RRC phase (RRC capacity)
-
Member
Reputation: 163
Re: congestion in RRC phase (RRC capacity)
How about RAB? is there any differences?
Bookmarks