-
Member
Reputation: 20
propagation delay ?
Hello guys.
I need to know how to run pmpropagation delay on E******* OSS. I don't know where can i run this parameter and save the results for example for 1 hour. So i can see which cells are overshooting or not.
Could any of you help me ? Thanks in advance.
-
2011-03-18 02:22 PM
# ADS
Circuit advertisement
-
Member
Reputation: 177
Re: propagation delay ?
hi bigorbi
you can reach pmpropagationdelay counter in nodeb status. Connect the nodeb via moshell and give a "pmr" command. then choose propagation report.
BR
Originally Posted by
bigorbi
Hello guys.
I need to know how to run pmpropagation delay on E******* OSS. I don't know where can i run this parameter and save the results for example for 1 hour. So i can see which cells are overshooting or not.
Could any of you help me ? Thanks in advance.
-
Member
Reputation: 20
Re: propagation delay ?
Originally Posted by
sonerss
hi bigorbi
you can reach pmpropagationdelay counter in nodeb status. Connect the nodeb via moshell and give a "pmr" command. then choose propagation report.
BR
yes i know pmr command but i couldn't find propagation report there.let me check again.
-
Member
Reputation: 20
Re: propagation delay ?
when i write pmr command after connecting rbs, these options are coming to the screen ;
1) Carrier Average Rssi and Transmitted Power
2) Downlink RadioLink Setup Success Rate
3) Uplink RadioLink Setup Success Rate
4) HSPA Throughput
5) HSDPA Congestion
6) HSDPA CQI total
7) HSDPA CQI rop by rop
8) HsDschResources AckNack rop by rop
9) HSDPA Measurements IubDataStreams
10) HSDPA Frame problems
11) HSDPA Usage rop by rop
12) HSDPA Codes rop by rop
13) HSDPA Power rop by rop
14) HSDPA Throughput per SPIxx
15) HSDPA Throughput per SPIxx-PQ
16) HSDPA Iub Flow Control
17) Total EUL Throughput and Efficency Factors
18) EUL Throughput and Efficency Factors rop by rop
19) Total EUL stuff
20) EUL stuff rop by rop
21) Total IBHOs and rejects
22) IBHOs and rejects rop by rop
23) Total UplinkBaseBandPool SetupFailures
24) Total UplinkBaseBandPool SetupFailures rop by rop
25) Total DownlinkBaseBandPool Allocation Rejects
26) DownlinkBaseBandPool Allocation Rejects rop by rop
27) Total DownlinkBaseBandPool RlSetupAttempts
28) DownlinkBaseBandPool RlSetupAttempts rop by rop
29) Total DownlinkBaseBandPool RlSetupFailures
30) DownlinkBaseBandPool RlSetupFailures rop by rop
31) Total DownlinkBaseBandPool RlAdditionFailures
32) DownlinkBaseBandPool RlAdditionFailures rop by rop
i couldn't find anything about propagation between these options.
-
Member
Reputation: 177
Re: propagation delay ?
Hımm
I checked my pmr command.. and we have got a report which name is "Carrier Prach Total" and this report gives you propagationdelay values..
1) Carrier Average Rssi and Transmitted Power
2) Carrier Prach Total
3) Carrier Prach per rop
4) Downlink RadioLink Setup Success Rate
5) Uplink RadioLink Setup Success Rate
6) HSPA Throughput
7) HSDPA Congestion
8) HSDPA CQI total
9) HSDPA CQI rop by rop
10) HsDschResources AckNack rop by rop
11) HSDPA Measurements IubDataStreams
12) HSDPA Frame problems
13) HSDPA Usage rop by rop
14) HSDPA Codes rop by rop
15) HSDPA Power rop by rop
16) HSDPA Throughput per SPIxx
17) HSDPA Throughput per SPIxx-PQ
18) HSDPA Iub Flow Control
19) Total EUL Throughput and Efficency Factors
20) EUL Throughput and Efficency Factors rop by rop
21) Total EUL stuff
22) EUL stuff rop by rop
23) Total IBHOs and rejects
24) IBHOs and rejects rop by rop
25) Total UplinkBaseBandPool SetupFailures
26) Total UplinkBaseBandPool SetupFailures rop by rop
27) Total DownlinkBaseBandPool Allocation Rejects
28) DownlinkBaseBandPool Allocation Rejects rop by rop
29) Total DownlinkBaseBandPool RlSetupAttempts
30) DownlinkBaseBandPool RlSetupAttempts rop by rop
31) Total DownlinkBaseBandPool RlSetupFailures
32) DownlinkBaseBandPool RlSetupFailures rop by rop
33) Total DownlinkBaseBandPool RlAdditionFailures
34) DownlinkBaseBandPool RlAdditionFailures rop by rop
Start Time: 2011-03-18 07:30:00 End Time: 2011-03-18 08:15:00
Object AvgPropDelay AvgRxPreambleSir ReceivedBlockSuccRatio pmNoPreambleFalseDetection pmSuccReceivedBlocks pmUnsuccReceivedBlocks
Sector=1,Carrier=1 1.5 -16.4 98.1 19 1778 34
Sector=1,Carrier=2 0.7 -16.7 99.5 9 2930 15
Sector=2,Carrier=1 2.8 -15.8 97.0 109 5239 161
Sector=2,Carrier=2 3.8 -15.2 92.8 148 3423 267
Sector=3,Carrier=1 4.3 -16.4 98.1 63 5381 104
Sector=3,Carrier=2 4.1 -18.1 99.7 42 27326 79
but you can one more way to reach propagation values
in nodeb layer you can give this command
pmx . pmPropagationDelay -m 1
This command gives you propagationdelay samples
BR
Im waiting your thanks and rep also
Originally Posted by
bigorbi
when i write pmr command after connecting rbs, these options are coming to the screen ;
1) Carrier Average Rssi and Transmitted Power
2) Downlink RadioLink Setup Success Rate
3) Uplink RadioLink Setup Success Rate
4) HSPA Throughput
5) HSDPA Congestion
6) HSDPA CQI total
7) HSDPA CQI rop by rop
8) HsDschResources AckNack rop by rop
9) HSDPA Measurements IubDataStreams
10) HSDPA Frame problems
11) HSDPA Usage rop by rop
12) HSDPA Codes rop by rop
13) HSDPA Power rop by rop
14) HSDPA Throughput per SPIxx
15) HSDPA Throughput per SPIxx-PQ
16) HSDPA Iub Flow Control
17) Total EUL Throughput and Efficency Factors
18) EUL Throughput and Efficency Factors rop by rop
19) Total EUL stuff
20) EUL stuff rop by rop
21) Total IBHOs and rejects
22) IBHOs and rejects rop by rop
23) Total UplinkBaseBandPool SetupFailures
24) Total UplinkBaseBandPool SetupFailures rop by rop
25) Total DownlinkBaseBandPool Allocation Rejects
26) DownlinkBaseBandPool Allocation Rejects rop by rop
27) Total DownlinkBaseBandPool RlSetupAttempts
28) DownlinkBaseBandPool RlSetupAttempts rop by rop
29) Total DownlinkBaseBandPool RlSetupFailures
30) DownlinkBaseBandPool RlSetupFailures rop by rop
31) Total DownlinkBaseBandPool RlAdditionFailures
32) DownlinkBaseBandPool RlAdditionFailures rop by rop
i couldn't find anything about propagation between these options.
-
Post Thanks - 1 Thanks
-
Member
Reputation: 20
Re: propagation delay ?
Originally Posted by
sonerss
but you can one more way to reach propagation values
in nodeb layer you can give this command
pmx . pmPropagationDelay -m 1
This command gives you propagationdelay samples
BR
Im waiting your thanks and rep also
thanks for your answer soner but i want to ask you one more thing,
with this command for example i want to take 2 hour propagation delay. it gives me in 15 min rops and it doesn't sum them. For example;
7.00 - 7.15
447,356,789,0,0,0,0,0,0,0,0,0,0,0
7.15-7.30
478,358,467,35,0,0,0,7,0,0,0,0,0,0
so from 7.00 to 7.30 actual values are the sum of these values right ? can't i arrange that ROP period to 2 hours instead of 15 mins? is there any way to do that ?
-
Member
Reputation: 177
Re: propagation delay ?
No way man
moshell gives you value always 15min. rops.. you can prepare this value for using excel(maybe you can write a macro )... but you can get 2 hours value for using "-m 2"
BR
Originally Posted by
bigorbi
thanks for your answer soner but i want to ask you one more thing,
with this command for example i want to take 2 hour propagation delay. it gives me in 15 min rops and it doesn't sum them. For example;
7.00 - 7.15
447,356,789,0,0,0,0,0,0,0,0,0,0,0
7.15-7.30
478,358,467,35,0,0,0,7,0,0,0,0,0,0
so from 7.00 to 7.30 actual values are the sum of these values right ? can't i arrange that ROP period to 2 hours instead of 15 mins? is there any way to do that ?
Im waiting your thanks and rep also
Last edited by sonerss; 2011-03-18 at 08:24 PM
-
Member
Reputation: 29
Re: propagation delay ?
Originally Posted by
bigorbi
thanks for your answer soner but i want to ask you one more thing,
with this command for example i want to take 2 hour propagation delay. it gives me in 15 min rops and it doesn't sum them. For example;
7.00 - 7.15
447,356,789,0,0,0,0,0,0,0,0,0,0,0
7.15-7.30
478,358,467,35,0,0,0,7,0,0,0,0,0,0
so from 7.00 to 7.30 actual values are the sum of these values right ? can't i arrange that ROP period to 2 hours instead of 15 mins? is there any way to do that ?
Just do pmx . pmPropagationDelay -m 2 -a
This will give you an aggregation for 2 hours.
Why don't you run a WMRR. Goto performance/RNO/WMRR and select the cells and the time you want to run.
-
Re: propagation delay ?
Originally Posted by
tsiz
Just do pmx . pmPropagationDelay -m 2 -a
This will give you an aggregation for 2 hours.
Why don't you run a WMRR. Goto performance/RNO/WMRR and select the cells and the time you want to run.
WMRR can not give us serving area distance of each cell same as the values for PropagationDelay am i right?
It it is wrong could you please explain haw we can do it?
@Sonerss:
With PMR command in RNC i could not see the option that you have posted here i do not know what is the differences in your output and mine !
Thanks
Thanks
Last edited by electron; 2011-03-19 at 05:45 AM
-
Member
Reputation: 177
Re: propagation delay ?
Hi
So how can we get all cells pmPropagationDelay values from RNC??
BR
Originally Posted by
tsiz
Just do pmx . pmPropagationDelay -m 2 -a
This will give you an aggregation for 2 hours.
Why don't you run a WMRR. Goto performance/RNO/WMRR and select the cells and the time you want to run.
Bookmarks