LG CU500 on TEMS almost done!

[telwind]

right, is the same in my LG CU500, but the key is 277634#*#, then port settings, then diag settings, but HERE there/s not something like "QUALCOMM USB" or anything else, there`s just "UART SET FOR DIAG, USB SET FOR DIAG, NULL PORT" I already tried according with the word attach of this forum, and I could enable the measurements like rxlevel, rxqual and TA, but there`s not FER, DTX POWER, SQI, C/I. I dont know if there's a "qualcomm interface" for my LG CU500 works fully on TEMS INVEST 9, or is just maybe a driver that I`m missing....

you should select 'USB SET FOR DIAG'

if it is still not work for you. this model interface may be not fully supported by TI I guess

[hugotg83]

as i know so far, some parameters are collected based on the proprietary algorithms. although they are based on qualcomm chipsets (detected and can be used with tems) but the functions are not fully supported.

But this model appears on Tems 9 compatible devices

[terryfrancois]

do you know where I can download the drivers for LG cu500 QUALCOMM? or do yoy know how to activate qualcomm interface (mode) in the mobile? I just know the "secret menu" 277634#*#, but there`s not any qualcomm interface.
Regards

Did you try installing qualccom driver? Then configure your LG into a qualcoom MODE. I know it will works.

[parto_tegal]

LG CU500
SW version: CU500-MSM32701001-V10d-Jan-05-2007-CW-US
thanks!

Hi
Thought that the recommended FW is older that yours:
CU500-MSM3250-V08h-Feb-27-2006-CW-US

Even thought Ascom says about Qualcomm Chipset Based Devices:

"Some commercial Qualcomm chipset derived phones and data cards,
marked with an asterisk (*) below, may not have diagnostics reporting
enabled by default, and Ascom is not at liberty to distribute information on
how to enable this function. Customers desiring to use such devices with
TEMS Investigation therefore need to contact the relevant supplier or
operator in each case."

Is that the reason you doesn't get a proper measurement value on it?

[terryfrancois]

well, thx for the info, actually i just downgrade the FW 10d to
LG CU500 - V10c - 03-08-06 - US, and it is the same in tems (no c/i, no fer, no sqi). Maybe you know some link to download the older firmware below this reply (VO8H)
thanks in advance

Hi
Thought that the recommended FW is older that yours:
CU500-MSM3250-V08h-Feb-27-2006-CW-US

Even thought Ascom says about Qualcomm Chipset Based Devices:

"Some commercial Qualcomm chipset derived phones and data cards,
marked with an asterisk (*) below, may not have diagnostics reporting
enabled by default, and Ascom is not at liberty to distribute information on
how to enable this function. Customers desiring to use such devices with
TEMS Investigation therefore need to contact the relevant supplier or
operator in each case."

Is that the reason you doesn't get a proper measurement value on it?

[Piojo]

In tems 8.2 is the same... look the picture,

MS1 is k790, MS2 CU500, both dedicated,

Those information elements are not displayed for CU500...

regards,

[terryfrancois]

Sure, the same happened with logs recorded two years ago in tems 8.0.3, it seems there's a disable feature for this LG mobile

Thanks for ur comment

regards

In tems 8.2 is the same... look the picture,

MS1 is k790, MS2 CU500, both dedicated,

Those information elements are not displayed for CU500...

regards,

[Piojo]

Sorry for bad news, but there are more information elements not supported by tems for qualcom based phones...

In the attachment you can find the cross list for GSM & WCDMA in pdf. You can find the same list on your tems help file, the version that i use is for TI 9.0,



regards,

[crisnspro]

nothing about the driver, if some of the LG CU500/TU500 can not work in TEMS investigation, that is caused by NVM problem.

[terryfrancois]

NVM problem?? sorry, but what do you mean with that?

nothing about the driver, if some of the LG CU500/TU500 can not work in TEMS investigation, that is caused by NVM problem.