-
Member
Reputation: 67
ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Hi all :
I have ISHO Problem ..from 3G Huawei to 2G Huawei handover...please support
RAN -11 is the version of 3G RNC,,,
2G neighbors had been defined of the 3G cell
In Idle mode the 3G is reelecting to 2G
In active mode 3G is not able to perform handover
please support in case any parameter must be performed in 3G or 2G needs to be enabled or tuned
-
2010-10-11 01:19 PM
# ADS
Circuit advertisement
-
Member
Reputation: 54
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
my friend
check switch 3G 2G HO=ON
-
Member
Reputation: 67
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
What s the command ?
to check if it is on
-
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Originally Posted by
moslyi0891
What s the command ?
to check if it is on
You should check HO_INTER_RAT_CS_OUT_SWITCH, HO_INTER_RAT_PS_OUT_SWITCH is ON by command: LST UCORRMALGOSWITCH
-
VIP Member
Reputation: 1106
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Originally Posted by
moslyi0891
Hi all :
I have ISHO Problem ..from 3G Huawei to 2G Huawei handover...please support
RAN -11 is the version of 3G RNC,,,
2G neighbors had been defined of the 3G cell
In Idle mode the 3G is reelecting to 2G
In active mode 3G is not able to perform handover
please support in case any parameter must be performed in 3G or 2G needs to be enabled or tuned
hi friend please check on the HO margin of system 3G and check on the RNC and BSC have neighbor each other
We can share knowledge to all guy join with Wire Free Alliance.
Many Thank,
Best regards,
TEMS_Engineer
-
Member
Reputation: 172
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Originally Posted by
moslyi0891
Hi all :
I have ISHO Problem ..from 3G Huawei to 2G Huawei handover...please support
RAN -11 is the version of 3G RNC,,,
2G neighbors had been defined of the 3G cell
In Idle mode the 3G is reelecting to 2G
In active mode 3G is not able to perform handover
please support in case any parameter must be performed in 3G or 2G needs to be enabled or tuned
Check if InterRAT is enabled at RNC level,feature is ON and whether everything is correctly defined in the CN (outer cells definitions). Can you see from the trace if the RNC sends all messages - for entering compressed mode , Measurement control messages and etc..
-
Member
Reputation: 73
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Originally Posted by
moslyi0891
Hi all :
I have ISHO Problem ..from 3G Huawei to 2G Huawei handover...please support
RAN -11 is the version of 3G RNC,,,
2G neighbors had been defined of the 3G cell
In Idle mode the 3G is reelecting to 2G
In active mode 3G is not able to perform handover
please support in case any parameter must be performed in 3G or 2G needs to be enabled or tuned
Check the GSM cell capability setting, check whether the MSC has "Service Handover Indicator" sent in the "RAB assignment" message not to allow 2G handover, 2D, 2F, 3A, 3C etc. event trigger parameters.
-
Member
Reputation: 78
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Originally Posted by
agenov
Check if InterRAT is enabled at RNC level,feature is ON and whether everything is correctly defined in the CN (outer cells definitions). Can you see from the trace if the RNC sends all messages - for entering compressed mode , Measurement control messages and etc..
Moreover, supposed to check neighbor list in RNC as well
-
Member
Reputation: 58
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Hi, I hope you have solved your problem right now. But just in case you must do as follows.
- Add external GSM cell definition in RNC
- Add IRAT neighbors relationship
- Turn on IRATHOEN switch in BSC
For the mml commands you can use as example this.
ADD UEXT2GCELL:GSMCELLINDEX=5717, GSMCELLNAME="PTN571A", MCC="704", MNC="01", RAC=H'00, CNOPGRPINDEX=0, LAC=402, CFGRACIND=REQUIRE, CID=5717, NCC=5, BCC=7, BCCHARFCN=238, BANDIND=PCS1900_BAND_USED, RATCELLTYPE=EDGE, USEOFHCS=NOT_USED, NCMODE=NC0, SUPPRIMFLAG=FALSE, SUPPPSHOFLAG=FALSE, CIO=0, NBSCINDEX=0, LDPRDRPRTSWITCH=OFF;
ADD U2GNCELL:RNCID=3001, CELLID=40351, GSMCELLINDEX=5717, BLINDHOFLAG=FALSE, NPRIOFLAG=FALSE, CIOOFFSET=0, QOFFSET1SN=0, QRXLEVMIN=-50, TPENALTYHCSRESELECT=D0, TEMPOFFSET1=D3, DRDECN0THRESHHOLD=-18, SIB11IND=TRUE, SIB12IND=FALSE, MBDRFLAG=FALSE, MBDRPRIO=0;
Hope it works.
Regards.
P.D. All The values are for example.
-
Junior Member
Reputation: 12
Re: ISHO Problem ..from 3G to 2G handover...Huawei,,,,,,please support...urgent
Ok if you have all the neighbour definitions correct, then the problem lies in the core network.
Activate a core trace and have a look at the messages that are coming back from the 2G core in response to the messaging sent from 3G.
Then make sure all of your routing and HLR information is correct, ie routing tables, provisioning, UE capability etc.
This is assuming your neighbour definitions are correct. If they are not then...
Bookmarks