Search:

Type: Posts; User: bawbag11; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    6,123

    Re: LTE Maximum DL throughput Issue

    Hi,

    Could try a simple test for TX limitation but you need 2 users & 2 Ue to test but second Ue (and user) can be regular one.
    1. Start download with your test Ue on one sector, let it get to max...
  2. Replies
    6
    Views
    4,192

    Re: Refarming PS Data Compression

    Hi,

    My comment having tried similar is good luck, you will need it :) Lots of old junk out there embedded in all sorts of kit use 2G only. Many new Iot products (think bike hire company) use 2G...
  3. Question Re: Flexible Bandwidth based on overlap carriers

    Hi,

    1. Camping was allowed on both carriers so users who got onto the 5MHz one had poor performance in comparison to 10MHz, you can configure differently of course however the whole cell layer...
  4. Question Re: Flexible Bandwidth based on overlap carriers

    Hi,

    No experience on 1900, but on 2100:
    Tested overlap carriers however it was not any real benefit. With 1x10MHz + 1x5MHz overlapped by 600kHz the performance on both were OK with no load but in...
  5. Replies
    4
    Views
    1,724

    Re: ALU neighbourCellPrio in WIPS

    Normally WIPS will not allow neighbour without priority set. The priority is used in soft handover when neighbour list concatenation happens and you get the highest priority ones sent in the...
  6. Replies
    0
    Views
    1,309

    Download A*toll.Std.x64.3.2.1.6837

    Not seen this posted before so here is link (installer only) for Atoll 64 bit ver 3.2.1.6837. Apologies if duplicate.

    RAR file password is atoll ---> atoll6837.rar (4shared, 78MB)

    BB
  7. Question Re: E1/T1 frequent alarms/Clock sync issues in WCDMA

    Hi,

    I would definitely do a loopback test to double check the TX circuit. If TX Network is IP you are using pseudowire and too many times the TX people avoid setting the correct CIR rate end to...
  8. Question Re: E1/T1 frequent alarms/Clock sync issues in WCDMA

    1) what are the immediate practical outcomes of an E1/T1 active alarm Or clock sync alarm? Audio distortion and lost signalling possibly leading to dropped calls / SHO failures and call setup...
  9. Re: Huawei_Detected Set Information Without DT/NASTAR

    Use Query Result in M2000 to show neighbour statistics. This includes SHO attempts / success for both configured and also detected neighbours that have been added to active set (assuming you have...
  10. Re: PS IRAT Improvement - RAC Configuration for GSM NBRs

    Made no difference in my network. Seems more config work for no gain. Currently we have it off. Irat performance ok as long as PS on the GSM cell is not congested. Check usual suspects on the GSM...
  11. Replies
    5
    Views
    2,546

    Re: RRC REJECTED (NODEBRESUNAVAIL) - Huawei

    If the other cells are working OK check allocation of BB resource. if the other cells are not working then reset the NodeB, still no then check the config. Is the NodeB connected by Ethernet or E1?...
  12. Download Re: Wray Castle RP2400 Introduction to UMTS Optimization

    Hi Polo, I cannot attach in one part as it is too large (max attach 3.8MB) and splitting would make more than 10 parts. is there any file sharing site that you can access and I will upload it there?...
  13. Download Wray Castle RP2400 Introduction to UMTS Optimization

    Apologies if already posted..

    Wray Castle RP2400 Introduction to UMTS Optimization

    Link:4shared.com [47MB]

    password: finetopix.com
  14. Replies
    9
    Views
    7,412

    Re: PCpich Power in UMTS

    AFAIK:

    MaxPCPICHPower & MinPCPICHPower are only of use when you use LDC/R algo. In my network the setting are left as default as we dont use the PCPICH for load control:


    List PCPICH...
  15. Replies
    3
    Views
    1,795

    Re: High DCR due to high IRAT FR

    Do a UEXT2GCELL & check correct BCCH / BSIC etc. Double check in BSC it is same.
    Check U2GNCELL for the neighbour relation and see if it is ok.
    Check UCELLINTERRATHOCOV is blank or same as other...
  16. Replies
    5
    Views
    2,457

    Re: Tilt Strategy in case of UMTS900/GSM900

    From my experience you need to do 3 things:

    1. Maintain G900 coverage at all costs, if not the customer will complain.
    2. Deal with overshooting cells, tilt etc while trying not to affect point 1...
  17. Replies
    40
    Views
    16,165

    Re: Mentum Ellipse 8.2

    Hmm:

    Seems to have all the files required?

    ftp://huntervalleyaviation.com.au/Mentum_VHA/

    BR
  18. Re: cell camping on other network provider problem?

    Interesting, Seen some issues where phone will camp on foreign network but when manually search it does not find the home network but this was timing. If your getting no network access and the radio...
  19. Re: cell camping on other network provider problem?

    Large difference in network timing between two networks?

    Whats the error message on the phone when manually register with home network after amped on neighbour country cell?
Showing results 1 to 19 of 21