.
Thanks Magno, could you please explain more what exactly is this? And if any documents explain signaling.
Regards,
Type: Posts; User: Mdaf; Keyword(s):
.
Thanks Magno, could you please explain more what exactly is this? And if any documents explain signaling.
Regards,
Hi,
In my network if you insert SIM in a mobile handset it can camp on TDD and FDD, but when same SIM card is used on CPE it will only camp on LTE TDD and if there is no TDD coverage but there...
Hi,
I need your help to understand how's the Qout and Qin is detected in LTE.
I know the general ideal, but i couldn't understand what its meant by table 7.6.1.1 in TS 36.133
Could anyone help...
Hi,
If we assume that we have disabled group B preambles (large size) and a UE has really big message to be sent, what will happen? Does it mean that the UE will distribute his PRACH on more...
Hi,
forgive me for my ignorance but I have very basic question.
in LTE we have refernce signal, and in case of using more than one antenna port we have to dtx the other refernce signal at the same...
Hi,
I have checked the measurement control sent to the UE after active set update and I have found the below info inside the measurement report, Can anyone please explain what does measurement...
Hello,
whats are the differences between edch transbport block size table 0 and 1 for 10ms?
many thanks
Hello, assuming source cell f1, this cell has f2 and f3 as ngbrs, Assuming both ngbrs have the same coverage priority defind in hopi, which freq would the rnc instruct the ue to search for and based...
Many thanks for the valuable info
Hello,
Does anyone know if Dc-hsdpa is supported in India? And which operator.
many thanks
Hello,
have anyone noticed any signal issues with samsung s6 in their netwrok, also is there any issues in download speed on 3G or LTE?
many thanks.
Hello, this is for event 6a not 6b.
Hello,
how can we enable event 6b in nsn, if so are there any counters to check?
Hello,
Whats the difference between cm service request and establishment cause sent on rrc request.
why would the ue send the sevice needed twices even if the cm service request is sent to core...
Hello,
We all know that Ue calculate the necessary power to send PRACH and if no acknowledgement on AICH it will increase the power and so on till it receives AICH, Now assume that the ue has...
Hello,
How does the ue know that there is hsdpa enabled on the cell showing h symbol while on idle mode, or pch or fach mode
Intresting but do you know why?
Hello,
I have noticed the following scenario on different TEMS handsets at different network locations.
When you enter and area with pilot polution the TEMS goes to other operators 3G!! Keeping...
Hello,
I've read somewhere (i can't remember where) that you need relatively high bit rate at the ul to have high bit rate on the downlink to be able to acknowledge the downlink, it seems logic...
Hello,
The below message is found in System Info 2quarter (3G_SEARCH_PRIO: yes (indicates if 3G cells may be searched when BSIC decoding is required)).
Could anyone please explain what does it...
Hello,
Could the ue perform 2G to 3G reselection during Routing area Code signalling on a 2G cell?
i.e the UE stop signaling before completing UE Routing LU and reselect to 3G
Could you please explain what do you mean by vendor specific sib2 quarter
Many thanks for the valuable info how to speed the reselection, my main concern was to know the average time to reselect again under normal circumstances.
Hello,
Do we have standard time for reselection from 2G to 3G, for example if IRAT took place from 3G to 2G during decidcated mode then after normal release UE will perfom LU on 2G then the Ue...
Hello, I have nokia 3g experince, i just have a question how do you compare nokia 3g to huawei and zte 3g in term of flexibity of optimization, counters, troubleshooting, opportunities to optimize...