I've got a radio that blinks red, orange, pause, repeat.
This has been wiped and programmed with a known good batch.
It blinks even when off, just with the battery connected.
Any ideas what the...
Type: Posts; User: Shuttleman; Keyword(s):
I've got a radio that blinks red, orange, pause, repeat.
This has been wiped and programmed with a known good batch.
It blinks even when off, just with the battery connected.
Any ideas what the...
Hello,
The dual battery charger 300-00290 has been featured in SRH, STP and SC series.
Do even the first SRH-era chargers support stp-batteries (and hence SC)?
Hi,
I bought a Sepura rucksack.
It does have a (dead) battery.
No power supply was with it, neither a charger.
Is there any documentation of these available?
I would need the pinout for the...
Mtm800 uses 5V ttl and mtm800e 3.3V ttl. The bricks are not the same..
Just for shits&giggles, trying to document as much as possible :-)
The methods for hidden menus are known on full- and limited keypad models - why not document this too.
Full keypad portables and mobiles can be started with * pressed at poweron. This will enter engineering mode directly at startup.
How does one enter engineering mode with limited keypad...
I have a stp8040 with the same problem. Radio works, but does not charge. Battery and charger substituded - they work.
Has someone changed the charging ic? Is it the same in stp9000-series?
it will most probably not. The hardware id is hard to match. Have not been able to recreate hardware id on virtual hardware.
Wow.
That's harsh. Although the material does include a lot of IP.
A side question;
I've got an earlier version of RM2 activated. Is the activation valid for this version too?
Thank you.
Still, most weird.
CPS+ v7.4, (depot) still states:
The radio codeplug version (0865) is not supported by CPS, please import the release packet for this codeplug first
So, still...
Hi,
Very much appreciated, the MTP8550EX would however require R36 file.
Btw, is there any way to import MR17 included z19 files to standard CPS, or must Depot be used?
Does someone have MR17 RPK or .z19 for MTP8550EX?
I've got one with the newest firmware, and the CPS says the codeplug version is not supported. Weird.
Once again, STP8X, not STP8000.
STP8X pinout, radio view top left 1, top right 2 and so on.
1 Sasi?
2 Mic-?
3 ? SPKR+?
4 ? SPKR-?
5 GND
6 Mic+?
7 GND?
8 ?
9 3,6V?
Stp9240 last four digits:
N0001: GPS, has man-down
20001: no GPS, has man-down and shows UBLX, unlicen in the hidden menu.
So the hw is present, but how does one enable it?
I've been digging and doing this back and forth;
- Updating a template resets any customization to language strings. This will need verification if it applies to all templates.
There are many...
Hi,
Is there a possibility to import language packs into RM2?
I would like to change the primary language. Or is the only option to manually translate each?
Sorry, the given pinout above is for STP8000/STP9000. Not for STP8X (ATEX).
I need the pinout to build a programming cable for STP8X, it connects to the side connector (RAC), it doesn't have a...
Sorry, could you post the picture somewhere else? It seems I don't have the rep power needed to view attachments.
Hi,
Does anyone have information on how to build a programming cable for Sepura STP8X-series radios?
It attaches to the side connector and that connector is different from the normal STP8/9000...
Hi,
Found this for STP8000 and STP9000:
http://www.finetopix.com/showthread.php/38167-SEPURA-hidden-Menu
How do one access these on STP8240 or STP9240 with limited or no keypad (includes STP9140...
I got the PUK from the original seller of the radio. Thankfully.
For any attempts to brute-force it;
auto-hotkey with ~600ms/try is the fastest that will work on my setup (Win7 32bit virtual...
Set pin=**** in ISSI management. Update pin/puk in the batch. When programming and it asks for pin - do not enter anything.
This works for pin, not puk!
Also, found in manual.. *facepalm*
This was really odd. It didn't ask for PIN on startup, but then RM toolbox asked for PUK.
I tried to create a similar setup on a SRG3500W for testing, but it asks for pin (0000) or can even be set...
Hi,
Let me guess? UW-band, sticker on top that says "radlink"?
I'm facing the same issue. Did you ever resolve this?
Best regards,
Martin