Search:

Type: Posts; User: ash98; Keyword(s):

Search: Search took 0.01 seconds.

  1. Replies
    64
    Views
    47,860

    Re: ATOLL 3.4.0 Portable WITH MED!!!

    for some reason Junior Member here can't see the attachment but thanks for sharing the link, will give a try.
  2. Replies
    3
    Views
    1,650

    Question Re: Carrier Aggregation Power

    A simple approach without load balancing:
    Priority setting - set the 20MHz carrier a higher priority so UE would camp on it most of the time. Your power setting will depends on your link budge and...
  3. Replies
    5
    Views
    3,308

    Re: Rank3 Rank4 Low Utilization

    Thanks Subway, what you said make sense but we do have TM4 configured on the site. UE penetration is one issue but based on the counter for UE CAT it seems we should have a good amount of UE supports...
  4. Thread: PUCCH SINR

    by ash98
    Replies
    3
    Views
    2,858

    Re: PUCCH SINR

    Agree with this, if you have 4Rx deployed you should go for 4 way IRC to better deal with high UL noise or high interference.
    You don't deal with PUCCH/PUSCH SINR unless you do Differential UL...
  5. Replies
    7
    Views
    2,878

    Question Re: lte air interface utilization

    Most high DL PRB utilization normally related to too many cell edge users which use a lot of physical resources, if you only have a mid-band carrier regardless the bandwidth you will always...
  6. Replies
    5
    Views
    3,308

    Rank3 Rank4 Low Utilization

    Our Rank3 and Rank4 utilization is very low on the 4x4 carriers, however rank 2 can go up to 75% to 85%. Would anyone share some of their experience for 4x4 deployment and how to bring up rank3/4...
  7. Replies
    1
    Views
    2,017

    Original Re: CSI Reporting Modes

    This question is unclear because CSI includes many UE reports like CQI, RI and PMI. This is highly dependent on how the eNB SWbis configured, like what TM mode is used, PUCCH resource assignments for...
  8. Replies
    7
    Views
    3,555

    Question Re: LTE 20M vs LTE CA 10M ?

    Not everyone have the luxury to have 20 MHz, in that case you will need to use 10MHz +10MHz.
    There are some advantages to have less bandwidth, two of the biggest ones are coverage and more PUCCH...
  9. Re: E*** (3G): Power configuration and "numberOfTxBranches"

    numberOfTxBranches depends on your transmission configuration, 2 if you use MIMO, 1 if you only have SISO or Receive diversity
    maxDlPowerCapability typically will be 460 in E/// which is 40 watts,...
  10. Replies
    3
    Views
    2,473

    Re: Excessive TCH interference

    Blaxian,

    How do you observe the interference on the TCH? Are you frequency hopping? What is the size of the hopping pool and how many TRx are in the pool?
  11. Re: how to display wcdma interference on tems discovery

    How do you define "Interference"?
    If it's Interference from the neighbor cell, you need to plot Ec/No on TEMS. I believe it's right next to the RSCP plot, you can do ranked or per PSC.
    If...
  12. Replies
    4
    Views
    3,263

    Re: CA band combination from UE capability message

    MaClaud,

    In this case 3GPP UE Release version maybe your best friend, that should give you UE capability for band combination in general. But please also note some of the 3GPP specific band...
  13. Replies
    2
    Views
    2,074

    Re: RSRP difference between in outdoor and inCar

    I don't have any documents but this is something hard to compare with because the serving cell may be in front of your car or behind your car that may give you a different result. I would say...
  14. Replies
    23
    Views
    78,748

    Re: What's new in iBwave 9.0

    The readme is not very helpful. I wonder if you could provide some more detail about how to set the server and what is the serial number for iBwave 9.
Showing results 1 to 14 of 15