Thank you @mounir34 and @hieuphong
Is there another thing to do instead of change PCI planning? In this case, coverage was adjusted!
BR,
Type: Posts; User: jenriqp; Keyword(s):
Thank you @mounir34 and @hieuphong
Is there another thing to do instead of change PCI planning? In this case, coverage was adjusted!
BR,
Team,
I've checked the previous posts about the rules and consecuences when we use MOD3 and MOD30
http://www.finetopix.com/showthread....3-6-30-rules-)...
Team,
I've checked the previous posts about the rules and consecuences when we use MOD3 and MOD30. Id like to know the interference impact in a practical scenary where 4 cells have the same PSS...
During the RIM request is possible that eNB doesnt receive the info from UTRAN . So eNB will be waiting within the timer period only .
Hi,
Thats right, but if you dont have config "code set" in the CN (its depend of the vendor) it doesnt work !! CN should be able to give the codec requested! . by the way, AMRC for HW it is a...
Hi all,
You should check these parameters:
1.- UtranPsHoSwitch
2.- INTERRATPOLICYCFGGROUP ----> UTRANHOCFG=PS_HO-1 (enabled)
3.- INTERRATHOUTRANGROUP:LOCALCELLID=2, INTERRATHOUTRANGROUPID=1,...
Hi,
K3014 includes whole traffic on TCH (also VAMOS)... But if you want to get statistics about VAMOS .. you can see R3550N2:Average Number of Busy VAMOS FR Channels / R3501:Mean Number of Busy...
Hi,
I refer to SImultaneous users over HSUPA (high noise for uplink) , thats increases RTWP . There are cases where its better HSUPA deactived.
BR
Hi,
Check if FACH users were increased and also FACH congestion after change.
BR
Hi,
What vendor do you work? make a PIM testing, also check if there is high load on HSUPA users
BR
Hi,
It depend, if you want to show by KPI then you can use counters of propagation delay with RSCP and EcNo (make an average per day maybe)
if you want to show by plot from drive test then you...
Hi,
thanks Shakeel_15 for your recommedation, maybe in indoor scenaries we can set RD or RU because there is not high mobility.
BR
Hi,
First, check if when you have good rxlev so the Rxqual keeps bad value and ocurrs drop call. then its probably interference issue (check frecuencies used on BCCH, TCH)
Second, if when you...
Hi experts,
What RBG Resource Allocation Strategy do you recommend? in your experience, have you seen any impact when use Round Down or Round Up. Hedex explanation says:
If this parameter is...
Hi,
yes, there is a command for HW, you just write "PING"
Hi,
you can check RTWP on real time? for example: if its HW vendor so open LMT node level and see monitor. also check load traffic, DC issue . maybe you have RRU problem. As said electron 0 its...
Mrs,
You need to know how many HSDPA / R99 users do you have in the cell, one option is to offload CS traffic to GSM (check cell capacity in GSM). Also, as metioned Mrs Sabila : expand 2nd SCCPCH/...
Dear,
Can I create golden list for VIP users for eNode B Huawei ? Anyone knows about that. Thank in advanced!!
Hi,
I think, you should do many testing:
- Do ping test
- check Tx with UDP/TCP testing and look if there are packet loss.
- check VSWR If issues are specific point or eNode B.
- check ETH...
Hi,
I think, your doubts has to be discussed in an independent post. So CQI values are sent by UE periodically to serving cell on uplink (HS-DPCCH). That informs to node B which data rate UE is...
Hi all,
Check TA and get users distributions because if you have many users far from cell that could be the problem, cell will do low mcs.
Hi yoyokdq,
This parameter is about cellresel, ue will strt to measurement UMTS when LTE signal is minor to -104. Means thats more restricted for to stay on LTE. Others KPI are good, users avg are...
Hi guys,
I made a change on sector 3 (more affected) where i put QRxlevMin to -58 and RRC noreply numbers were decreased but im not sure if that change is the responsable (on 03/03/16) because...
Hi Yoyokdp,
FFFFFFF means rest of IMSIs because the omstar only shows top ten imsi or cells.
Second, the issues ocurrs suddenly anyhours.. it doesn't depend a specific hour and it occurs on...
Hi team,
I've been working with CHRs file and OMstar where I can see the fails percent by no.reply, the results are:
1.- There is a TIMSI with 15% of access failure. How to get this IMSI?
2.-...