Hi,
We have been tested FDD-TDD CA with Sumsung Galaxy S7. But then you should check with Sumsung local office that this CA combinations is activated in sw.
Type: Posts; User: rsv12; Keyword(s):
Hi,
We have been tested FDD-TDD CA with Sumsung Galaxy S7. But then you should check with Sumsung local office that this CA combinations is activated in sw.
Hi,
Possible you will find an answer in this feature functional description :RAN1686: HSPA 72 Users Per Cell - "The code space of HS-SCCH# 2, 3 and 4 code can be dynamically used for the...
Hi,
What is the SW level? Is GSM to UMTS Ho activated?
Hi,
Is this project dead ?
Hi All,
Does anybody have an experience with NSN RL40 channel aware feature activation ? Is there any pitfalls?
Hi,
NSN does not have "hoType" parameter, E******* has it. NSN uses one parameter set for triggering compressed mode for inter-freq and inter-system feq. to measure. What to measure depends on the...
Hi,
In other words: single stream - the same symbol is transmitted in parallel by each antenna, let say in our case we have only two antennas. Receiver can get the same symbol twice. So,if for...
Hi, If you do not have this feature activated "RAN1686: HSPA 72 Users Per Cell" then the maximum number of HSUPA per cell is 20 (actually 19) limited by available signatures in E-RGCH/E-HICH...
Hi,
Check SIB3 message for idle mode cell reselection parameters and SIB4 for connected mode cell reselection parameters if activated.
Hi,
Check Open Loop Power Control parameters. Sometimes it could be the reason for missed calls. Do you know how many rach messages usually should be send in your network before UE get the answer...
Hi ALL,
We have the same problem with NSN. Many rejects because of AC Uplink. Any idea?
Where to send cv?
Very good question! ?
Hi all,
Yes , they are working. We are using some of them in our network. The only
thing that they are quite expensive.
Hi,
We are just planning to test this feature in our network. At the moment it is not clear how many UE support this option. For me it is also could be interesting to hear some feedback about this...
Hi all,
Does anybody has experience with "AMR with simultaneous HSDPA" feature activation in NSN network? We see that some UE drop the AMR call when simultaneously HSDPA channel is allocated. There...
Hi, may be before isho ue was at soft ho? Than RNC marges neighbouring lists from nodeb in soft ho to one list. check this.
Hi, what kind of transmission do you have? with 8xE1 you can get about 12mbps. For 14mbps per user or higher you need more E1 or ethernet. Do you using Suprem - with hsdpa scheduler max 10mbps or...
Hi. country and project time?
In NSN network there is a parameter Maximum target received wide band power for BTS witch default value in some case can limit the maximum HSUPA throughput. It should be changed to higher value. May...
Hi,
Did you find the answer? Because in our NSN we have the same behavior and I do not fully understand the reason for that.
Hi, just activate this feature at E also. Nowadays this is very important option , at the beginning of 3G there were some UE that did not work with cell PCH mode. But those UE already have gone and...
Hi,
Do you mean HSDPA? Probably you do not have Serving HS-DSCH Cell change and SHO feature activated. Then during cell change you go to FACH state and after to DCH , then some timer running witch...
Hi, it may be because of PRACH procedure failure. Did you check that all preambles sent by UE were received by WBTS?
Hi Optimplanner,
As I understood you have average 46 HSDPA users at one cells and your measurements show only 7.5mbps maximum (average) throughput?
Check the documentations , possible there is...