nec ipasolink, how to get GE/SFP port bandwidth via snmp ?

I encountered a strange problem, with my old NEC ipasso.
I can't add port bandwidth graphs to my Nagios monitoring.

I want to monitor the ports GE1 ... GE4, and SFP1/2,
But I can't find the required OID for the ports.
by SNMP, I find only the ports eth0.xx, bridgeXX and bcmXX

Below is my SNMP list of ports. no GE/SFP port.
Can anyone know if there is an opportunity to get values on the ports,
or is it just such an architecture ?

Thanks.

Code:

---

IF-MIB::ifName.1 = STRING: lo
IF-MIB::ifName.2 = STRING: eth0.1
IF-MIB::ifName.3 = STRING: inband
IF-MIB::ifName.11 = STRING: bridge1
IF-MIB::ifName.12 = STRING: bridge2
IF-MIB::ifName.13 = STRING: bridge3
IF-MIB::ifName.14 = STRING: bridge4
IF-MIB::ifName.15 = STRING: bridge5
IF-MIB::ifName.16 = STRING: bridge6
IF-MIB::ifName.17 = STRING: bridge7
IF-MIB::ifName.18 = STRING: bridge8
IF-MIB::ifName.19 = STRING: bridge9
IF-MIB::ifName.20 = STRING: bridge10
IF-MIB::ifName.21 = STRING: bridge11
IF-MIB::ifName.22 = STRING: bridge12
IF-MIB::ifName.23 = STRING: bridge13
IF-MIB::ifName.24 = STRING: bridge14
IF-MIB::ifName.25 = STRING: bridge15
IF-MIB::ifName.26 = STRING: bridge16
IF-MIB::ifName.27 = STRING: bridge17
IF-MIB::ifName.28 = STRING: bridge18
IF-MIB::ifName.29 = STRING: bridge19
IF-MIB::ifName.30 = STRING: bridge20
IF-MIB::ifName.31 = STRING: eth0.3
IF-MIB::ifName.32 = STRING: eth0.2
IF-MIB::ifName.41 = STRING: bcm2-1
IF-MIB::ifName.42 = STRING: bcm3-1
IF-MIB::ifName.8454144 = STRING: lldp1-1
IF-MIB::ifName.8519680 = STRING: lldp1-2
IF-MIB::ifName.8585216 = STRING: lldp1-3
IF-MIB::ifName.8650752 = STRING: lldp1-4
IF-MIB::ifName.8716288 = STRING: lldp1-5
IF-MIB::ifName.8781824 = STRING: lldp1-6
IF-MIB::ifName.16842752 = STRING: lldp2-1
IF-MIB::ifName.25231360 = STRING: lldp3-1

---

Good evening! Find a way? As relevant and me

I need time to remember everything.
but in the general case - no snmp.

The hardware architecture of the device is,
that ethernet ports are removed from the processor.

probably the processor - doesn't control their load.

I solved the problem with FE/GE port activation
and radio speed at IPASSO and maybe VR,
but not with snmp.

Attachment 41312

it seems that the block diagram of the relay is such that all these 6 ports are included in the L2 switch, and the control board is already included in it via the VLAN.

and by SNMP - we see the control card, with its internal ports.
but specific, external, ports - we do not see.

ifconfig on the control board, roughly corresponds to the SNMP. the log below.

Quote:

---

bridge1 Link encap:Ethernet HWaddr 58:C2:32:B0:4B:A0
inet addr:10.0.16.30 Bcast:10.0.16.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:120641173 errors:0 dropped:0 overruns:0 frame:0
TX packets:11990092 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1072092820 (1022.4 MiB) TX bytes:1133341848 (1.0 GiB)

---

but in fact there are only these three counters, bridge1 eth0 and bcm2,
type of what came and what went away. Without detail on Ge / SFP ports.

although I may be wrong,
perhaps in a newer software there are already new counters.
I didn't check latest SW, NEC unit left my lab.