PDA

View Full Version : 索爱手机读FLASH的一个小工具



GEZA
2007-04-05, 03:49 PM
索爱手机读FLASH的一个小工具,不过还需要DIV的加密狗。


需要运行userport,启动驱动,然后才能用setool,
那个userport.sy要拷贝到system目录下。
DOS窗口下运行:出现下面的提示表示可以连接手机了
C:\setool>setool
This is flash tool, v.0.7851. INVOKE WITH -? FOR HELP !!!
Special edition for: [Only registered and activated users can see links] ([Only registered and activated users can see links])
done by the_laser.
NOTE FOR CASE OF COMMANDS - THEY MAKE SENSE !
parameters is:
/0 /bADDR /lLENGHT - rip avr flash from ADDR LENGTH bytes
ex: /0 /b$400000 /l$10000
/1 /BADDR /LLENGHT - rip arm flash from ADDR LENGTH bytes
ex: /1 /B$01000000 /L$10000
/2 /gFILENAME - writes FILENAME into t610 gdfs ($400000)
ex: /2 /gT610_CLEAN.BIN
/3 /bADDR /lLENGHT - rip avr program flash from ADDR LENGTH bytes
ex: /3 /b$01000000 /l$10000
/4 /BADDR /LLENGHT /gFILENAME - write arm flash from ADDR LENGTH bytes
ex: /4 /B$01000000 /L$10000
/5 /bADDR /lLENGHT /gFILENAME - write avr flash from ADDR LENGTH bytes
ex: /5 /b$400000 /l$10000
/a - also boot arm, needed for /1 /4
Note - flash can only be WRITTEN by even addresses with boundary $10000
RESULT:Now you know
DISCONNECT CABLE BEFORE NEXT USE !!!!


如果提示是:
C:\setool>setool
This is flash tool, v.0.7851. INVOKE WITH -? FOR HELP !!!
Special edition for: [Only registered and activated users can see links] ([Only registered and activated users can see links])
done by the_laser.
NOTE FOR CASE OF COMMANDS - THEY MAKE SENSE !
parameters is:
/0 /bADDR /lLENGHT - rip avr flash from ADDR LENGTH bytes
ex: /0 /b$400000 /l$10000
/1 /BADDR /LLENGHT - rip arm flash from ADDR LENGTH bytes
ex: /1 /B$01000000 /L$10000
/2 /gFILENAME - writes FILENAME into t610 gdfs ($400000)
ex: /2 /gT610_CLEAN.BIN
/3 /bADDR /lLENGHT - rip avr program flash from ADDR LENGTH bytes
ex: /3 /b$01000000 /l$10000
/4 /BADDR /LLENGHT /gFILENAME - write arm flash from ADDR LENGTH bytes
ex: /4 /B$01000000 /L$10000
/5 /bADDR /lLENGHT /gFILENAME - write avr flash from ADDR LENGTH bytes
ex: /5 /b$400000 /l$10000
/a - also boot arm, needed for /1 /4
Note - flash can only be WRITTEN by even addresses with boundary $10000
RESULT:Now you know
DISCONNECT CABLE BEFORE NEXT USE !!!!
Exception EPrivilege in module setool.exe at 000089D0.
Privileged instruction.
C:\setool>
那就说明驱动没有正确启动,需要重新运行userport。

zl7246
2007-04-13, 05:02 PM
谢谢!!!!!!!!!!!!!

dzt5037
2007-04-19, 07:45 PM
感谢,感谢,感谢,感谢,感谢,感谢,感谢,感谢,感谢,

bt0
2007-04-22, 07:27 PM
好东西,下载来看看

rdqs
2007-04-24, 03:42 AM
hao dong xi ,da jia kan kan

xa_dudu
2007-04-26, 06:58 PM
用不了啊,搂主是不是看一下

dzt5037
2007-04-26, 08:07 PM
要在98下才能运行要在98下才能运行要在98下才能运行要在98下才能运行要在98下才能运行

kuqi
2007-04-27, 03:25 AM
DDDDDDDDD



DDDDDDDDDDDDD

GEZA
2007-04-27, 10:27 AM
C:\setool>setool
This is flash tool, v.0.7851. INVOKE WITH -? FOR HELP !!!
Special edition for: [Only registered and activated users can see links]
done by the_laser.
NOTE FOR CASE OF COMMANDS - THEY MAKE SENSE !
parameters is:
/0 /bADDR /lLENGHT - rip avr flash from ADDR LENGTH bytes
ex: /0 /b$400000 /l$10000
/1 /BADDR /LLENGHT - rip arm flash from ADDR LENGTH bytes
ex: /1 /B$01000000 /L$10000
/2 /gFILENAME - writes FILENAME into t610 gdfs ($400000)
ex: /2 /gT610_CLEAN.BIN
/3 /bADDR /lLENGHT - rip avr program flash from ADDR LENGTH bytes
ex: /3 /b$01000000 /l$10000
/4 /BADDR /LLENGHT /gFILENAME - write arm flash from ADDR LENGTH bytes
ex: /4 /B$01000000 /L$10000
/5 /bADDR /lLENGHT /gFILENAME - write avr flash from ADDR LENGTH bytes
ex: /5 /b$400000 /l$10000
/a - also boot arm, needed for /1 /4
Note - flash can only be WRITTEN by even addresses with boundary $10000

RESULT:Now you know
DISCONNECT CABLE BEFORE NEXT USE !!!!


要先运行UserPort.exe,将userport.sys复制到c:\windows\system32\drivers目录下。

dzt5037
2007-05-10, 08:16 PM
晕哟,不能用呢,有没使用成功的兄弟,说一声呀

GEZA
2007-05-10, 11:03 PM
很简单的工具哦,还不行那就是你的狗的问题了

亮仔
2007-05-19, 12:49 AM
我的DIV84装置安装成功后,运行setool不正常,手机都可以检测出来,但是读、写不正常,读取就不显示100%,直接断开电缆;而写是写到一半就over,有时候就不写,奇怪。我的DIV是才买的,是不是还根狗的版本有关?

GEZA
2007-05-19, 02:04 AM
没有遇到这样的事情;不过setool和div是不能同时用的

firewise
2007-05-23, 01:02 AM
没有遇到这样的事情.................

skip1978
2007-05-23, 06:57 PM
这个软件不好啊,还有其他更好的

firewise
2007-06-16, 08:28 PM
老外很早就搞出来啦...........

firewise
2007-06-18, 08:59 PM
请问有无支持新版本TEMS手机的软件?

woodandpig
2007-06-18, 10:39 PM
下了
不会用,呵呵

liyicool
2007-06-21, 03:11 AM
好东东,不知用啊,我只有DIV84,也不会用啊

hs2001
2007-07-07, 12:57 PM
下来看看啊!!!!!

toty
2007-07-23, 12:41 AM
XP不行的么????????

geza1
2007-07-23, 11:20 AM
XP下也是可以用的。

aleck_huang
2007-08-12, 03:20 AM
大家知道有什么工具可以读K790-flash呢,读出来我可以共享出来大家研究

aouizn
2007-12-17, 10:59 PM
GOOD SW? THANKS FOR SW

zhjd
2008-01-03, 11:13 AM
有DIV的破解版吗?或者注册文件都可以。

gsmart
2008-01-27, 04:22 AM
Hey!

How can I read GDFS of my original TEMS Pocket with this setool

wujun0938
2008-03-09, 03:32 PM
rt rreq fr req eq re req req qer qe eq

anita_2k
2008-04-27, 01:47 AM
Thanks admin for guidance. more power. ;)

shahram
2008-04-29, 07:05 AM
hi
i think it is time anyone publish the way to clone TEMS Pocket for T610.
any body knows?

br
shahram

亮仔
2008-06-01, 09:06 PM
换了个DIV加密狗,好了。原来以前那个狗不行,但是用来启动DIV软件可以。
SETOOL+DIV 很简单,至少比colneTEMS R320简单多了。

baoshizhi
2008-07-01, 01:32 AM
支持一下,制作TEMS T68或者T610必备的好软件!我就是用它来读出手机的GDFS,并算出TEMS T68的GDFS

jackylooo
2008-07-27, 07:59 PM
我沒有SETOOL 的DONGLE 無法讀取GDFS.BIN
不知哪位高手能分享一下解碼後的 TEMS T610 的GDFS 與IMEI嗎?萬分感激

baoshizhi
2008-07-29, 03:43 AM
此setool需要的不是SE TOOL的Dongle!
请仔细看楼主的帖子!

fmstereo
2008-07-29, 05:27 PM
命令怎么用啊?我要读T68的GDFS怎么读呢?

fmstereo
2008-07-29, 05:28 PM
C:\Flash_T68\OldTEMSVer>setool /0 /b$00D80000 /l$00270000
This is flash tool, v.0.7851. INVOKE WITH -? FOR HELP !!!
Special edition for: [Only registered and activated users can see links]
done by the_laser.
Terminator Dongle is present.
Serial number is:00072CF7
All ready. press Enter____

Main boot loop is begin.....
Bootstrap First Step ............ OK!
Bootstrap Second Step OK!
Bootstrap Third Step ........... OK!
Bootstrap Fourth Step ...FAIL
ASIC ID: 5B0702FF
bypass boot err:0106

jackylooo
2008-07-30, 01:20 AM
求TEMS T610 的GDFS 與IMEI
說錯了,我是想說我沒有DIV 的DONGLE 因此無法讀取GDFS.BIN
不知哪位高手能分享一下解碼後的 TEMS T610 的GDFS 與IMEI嗎?萬分感激

ciming
2008-07-30, 03:19 AM
有没有步骤啊!希望有个步骤

sanp007
2008-08-24, 05:23 PM
这个工具可以用,不过只能读些老型号!!T630以上机器读不了!!

zleizero
2010-02-02, 02:15 AM
这个工具可以用,不过只能读些老型号!!T630以上机器读不了!!

在哪里下载这个工具啊

zleizero
2010-02-02, 02:18 AM
请问管理员我为何不能下载附件啊?:(

zleizero
2010-02-02, 02:29 AM
[Only registered and activated users can see links]