PDA

View Full Version : Flashing Motorola V3xx



PaleNxtTel
2009-09-11, 12:23 PM
Dear Friends,

Does TEMS or NEMO support Motorola Handset V3xx for GSM measurements? :confused:
because as I can see from TEMS 8.03 lic that Motorola support only UMTS !!! (See the Pic)

If it does, I just received FW for V3xx. I didn't try it yet, actually I don't know how to install the FW for Motorola handset :L.
So if any one interesting for discussion and sharing the knowledge (and the FW) please PM me.

kaka.enine
2009-09-11, 02:35 PM
yes ...

it can support GSM-UTMS at TEMS & NEMO,
(correct me if am wrong)


ask parto_tegal how to flash it ... ;) ;)

fmstereo
2009-09-11, 04:35 PM
I know how to flash a v3xx.

PaleNxtTel
2009-09-11, 09:47 PM
Thanks Kaka

but do I need lic for GSM !!


yes ...

it can support GSM-UTMS at TEMS & NEMO,
(correct me if am wrong)


ask parto_tegal how to flash it ... ;) ;)

PaleNxtTel
2009-09-11, 09:57 PM
Interesting :cool:

can u share step-by-step for how to flash it.

Thanks


I know how to flash a v3xx.

PaleNxtTel
2009-09-12, 12:36 AM
Ok here u are the Flashing

http://www.4shared.com/file/131915500/c01cf2a5/MOTOROLA_Flash.html

you can try it and feed me back with the results.

for the password PM me

PW :: Next_Moto_Flashv3xx

Enjoy :D

parto_tegal
2009-09-12, 02:33 AM
Ok here u are the Flashing

http://www.4shared.com/file/131915500/c01cf2a5/MOTOROLA_Flash.html

you can try it and feed me back with the results.

for the password PM me

It's easier to use FB3:
http://rapidshare.com/files/262197930/FB3.rar
No password protected :D
Regards
parto_tegal

PaleNxtTel
2009-09-12, 07:32 AM
Thanks for your advice :D

Can u share Step-by-Step for how to flash Moto V3xx :L



It's easier to use FB3:
http://rapidshare.com/files/262197930/FB3.rar
No password protected :D
Regards
parto_tegal

parto_tegal
2009-09-12, 09:47 AM
Dear All...
I am so sorry, I was too na'if to judge the post of PaleNxtTel is not a good solution, it is actually the best one contains all resource to make your V3xx EFEM Phone...

Here we go....
1. Install the fb3.0.7 Software
2. After finished, run the software and run the keygen, enter name and unlock the F&B.
3. Install the Motorola_EU_Driver_Installation and connect your powered- ON V3xx Phone into your computer using Mini USB Cable.
4. On F&B Software, click Read button and back-up your original FW of your V3xx normal phone, just in case... :p
5. Then click Write button and appoint the firmware of 2007-07-16_185609.fb3 and check your normal FW. You need the same FW version with the EFEM Firmware version, it is R26117RK_U_98.50.0ER or the lower...
6. Then click Write data, wait until finish....

(I am sorry I have no phone to flash....)

Have a good luck...
parto_tegal

elche
2009-09-12, 12:32 PM
Have you tried connecting the phone before flashing , TEMS has support for several phones without the need of any special firmware , specially for 3G.

parto_tegal
2009-09-12, 07:22 PM
Have you tried connecting the phone before flashing , TEMS has support for several phones without the need of any special firmware , specially for 3G.

It's supposed to be a Qualcomm Based chipset phone, isn't it? Motorola needs a NETMON license to get connected with TEMS/NEMO Software, and EFEM License for Pocket View....
Regards
parto_tegal

crisnspro
2009-09-14, 12:28 AM
any one test it? I try to flash it but no winrar password.

chengmei
2009-09-14, 02:55 AM
the trouble is the phone boot loader, now the new version of boot loader can't support the old firmware

parto_tegal
2009-09-14, 05:47 AM
the trouble is the phone boot loader, now the new version of boot loader can't support the old firmware

Higher firmware version of the phone will need newer bootloader, but maybe it will not work well with lower version of EFEM/Netmon firmware :p

Regards
parto_tegal

crisnspro
2009-09-15, 02:54 PM
Ok here u are the Flashing

http://www.4shared.com/file/131915500/c01cf2a5/MOTOROLA_Flash.html

you can try it and feed me back with the results.

for the password PM me

already PM you, but no response.

wolverine
2009-09-17, 01:04 AM
Ok managed to find a V3xx and tried this solution. It works fine, both EFEM and NetMon interface are present.

Note: To enable the NetMon interface go to the phone menu -> USB Connection and choose Network Monitor.

To switch between the EFEM and the normal phone menu, press the menu key and the left soft key in quick succession.

Stepanich81
2009-09-17, 02:42 AM
May be valide code for hide/show EFEM: fast press menu 00**83786633* -show; menu 00**8378633* -hide

chengmei
2009-09-17, 05:42 PM
Higher firmware version of the phone will need newer bootloader, but maybe it will not work well with lower version of EFEM/Netmon firmware :p

Regards
parto_tegal


thank you for you reply. but where is the file " 2007-07-16_185609.fb3 " ,where can download it ?

dzt5037
2009-09-18, 10:18 AM
这个我知道,我以前搞过一台。。。

rval25
2009-10-17, 04:08 AM
please could u give as the password

regetdeluxe
2009-10-17, 10:42 PM
Does it really work?

xiaoduirensheng
2009-11-06, 05:48 PM
what is the password?

PaleNxtTel
2009-11-08, 09:41 AM
For every One looking for the Password here you are

PW :: Next_Moto_Flashv3xx

enjoy it :cool:

and please feed me back with the results

adrian_122003
2010-01-12, 12:57 AM
does anybody know how to flash the motorola v6 maxx to be usd in tems?
anybody has the file needes to flash on the phone?
thanks

yy19820503
2010-01-29, 12:37 AM
can you tell me how flashing v3xx tems

yy19820503
2010-01-29, 12:40 AM
can you share step-by-step for how to flash v3xx tems