PDA

View Full Version : Question SDCCH TRAFFIC



abdulkhodar
2009-05-22, 10:20 PM
Hello Expert
I work with siemens network, i want ask!!!
how to calculate SDCCH channel, its depend on traffic SDCCH or attemp SDCCH or mean holding time SDCCH or what ?
so we can get maximum TRX channel usefully, not trial and trial again.
please explained more detail bacause i am newer RF Engineer :D,
thank you very much for your answer

esteaan
2009-05-22, 11:28 PM
Its depends on several factors. In boarder areas, for instance, SDCCH traffic will be higher.

According to the standarts to calculate the SDCCH load per subscriber, there are four values to be considered:
- call attempts per subscriber per hour 1.1
- time for MOC/MTC setup signaling 3 sec
- time for Location Update 5 sec
- location updates per subscriber per hour 2.2.
The SDCCH load per subscriber is calculated as follows:
(1.1 * 3 sec + 2.2 * 5 sec) / 3600 sec = 0.004 Erl.

Regards

GSM_Huawei
2009-05-22, 11:41 PM
download link

wolverine
2009-05-23, 12:45 AM
I have attached an E******* document describing SDCCH dimensioning guidelines. Hope it helps!

http://www.4shared.com/file/107063733/2ca7c46f/E*******_-_SDCCH_Dimensioning_Guideline.html

alkelani
2009-06-01, 03:09 AM
nice document do you other one for sdcch dimensioning

kahnoie
2009-06-13, 08:13 PM
SDCCH Traffic (in Erlangs) = number of sub * SDCCH traffic in busy hour (in mE)

Regards,
Amit
agarwalamit081@gmail.com

m2m
2009-09-15, 01:17 PM
Not only traffic of SDCCH you might need to consider, you might need to consider attempt and SDCCH blocked call too base on trend. Sometime it is BTS problem which raise SDDCH attempt and blocked.

But if the trend show that the targeted cell always has high traffic and always high block call you might consider to add SDCCH channel, according to guideline and dimensionning rule.

Bloker
2009-12-27, 11:00 AM
Does siements have channel reconfiguration features? from TCH to SDCCH and vise versa or not?

RF engineer
2009-12-27, 10:02 PM
Hello Expert
I work with siemens network, i want ask!!!
how to calculate SDCCH channel, its depend on traffic SDCCH or attemp SDCCH or mean holding time SDCCH or what ?
so we can get maximum TRX channel usefully, not trial and trial again.
please explained more detail bacause i am newer RF Engineer :D,
thank you very much for your answer
you can put for 1-2 TRX 1 SDCCH ,3-4 put 2 SDCCh and 5-6 put 3 SDCCH these are as rule if the site on the LAC border you can increased.
but if you want to have SDCCH timeslot according to traffic take SDCCH/TCH ratio and then you can fined how many TS you need.
BR
RF

ddungu
2009-12-28, 01:10 PM
Hi,

You can also use the erlang B table to check if you have enough sd channels for sd traffic.

use 0.05% GOS.

justdream
2009-12-30, 09:26 PM
Hi,

You can also use the erlang B table to check if you have enough sd channels for sd traffic.

use 0.05% GOS.

My friend, please explain how to use Erlang B table
I forgot this issues, I have just used in my faculty,
please guide me, thanks a lot :hug: