E******* Mini Link Craft 1.1

[gsmmangi]

Hi,

Attached is the download link for E******* Minilink Operation & Maintenance software (Mini Link Craft 1.1)..

Password for zip file is "gsm"

Don't forget to say thank for those who find software good.

[Cost_Reducer]

...Hi everybody, :p

anybody here who can share MiniLink Craft 1.0, 1.1 or 1.2 ?
I need the software very urgently...:time:

ok, hope anybody can help me...

Thanky in advance...:)

[tanbao]

I have Mini link Craft, pm me

[ismaelhaider]

Thanks for the Good post

[tanbao]

I only have Minilink craft 1.1, but it working properly, do you need it???

[Ryuuken]

I have Mini link Craft 1.1 1.4 and 2.0.1

Pls, PM me if you need something and we'll arrange something

[Cost_Reducer]

Hello ,

whats new on ML Craft 2.0.x ? With 1.4 i have some problems after a swap of the NPU. I can`t reconfigured the new NPU rightly.

[sabila]

may all of u can share it at 4shared or rapidshare

many thanks for your attention

[Ryuuken]

I didn't have any problems with Craft 1.4
As for Mini link Craft 2.0.1 there are some news. It has little bit different interface. But basic news is that fully support new baseline for Mini link TN. You cannot access TN with software above 3.3.6 if you don't have Craft 2.0.1



Hello ,

whats new on ML Craft 2.0.x ? With 1.4 i have some problems after a swap of the NPU. I can`t reconfigured the new NPU rightly.

[Ryuuken]

What version do you need?

Btw, do you have access to any professional radio link planning tool like pathloss?
I tried to download pathloss 4.0 and that is ok, but unlocking is something else.
can you help me with this



may all of u can share it at 4shared or rapidshare

many thanks for your attention

[rasar00]

Hi,

Attached is the download link for E******* Minilink Operation & Maintenance software (Mini Link Craft 1.1)..

Password for zip file is "gsm"

Don't forget to say thank for those who find software good.
what is the use of this software

[Cost_Reducer]

what is the use of this software


with this software you can manage E\\\ MiniLink Traffic Node

[samershahin]

what is the use of this software
used for site field engineers to connect to traffic nodes transmission equipmnet of e*******, especially mmu2d...

[leosedf]

Links are down, Can we have a reupload?

Regards

[Cost_Reducer]

current version is ML Craft 2.3

[slavun]

Old info :)
2.4

[leosedf]

Nice! Any links?

[Cost_Reducer]

Old info :)
2.4

2.4?

pls upload this sw :p

and any description of new features?

[fonefreak]

i have 2.3 upgrade :)
above 50mb.. will try to share in some free time:rolleyes:

[slavun]

http://www.4shared.com/file/165583133/96278fa1/upgrade24.html

But 2.4 can be upgraded after u have 2.2

[Okoje]

hello bro & sist, what is the latest ver for Minilink Craft for acces Minilink TN E*******? Should we used bpftp server if we want to load configuration,upload SW baseline or SW module (MMU2,NPU,LTU), now I use Minilink Craft 2.1. I f i'm not mistaken there is ftp server include in this package software. Yesterday, i have upgraded successfully SW baseline to R16A30 (MLTN 4.2FP Software Release) with result: LTU 155e release SW R5B01 with product no. CXCR 102 004/1, RAU1 N 7/48 release SW R3A with product no. CXC 132 2623. Base on e-doc MLTN 4.2FP Software Release, for LTU 155e module & RAU1 N 7/48 doesn't meet the minimum requirement of release SW, which for LTU 155e min release SW R3E02 & RAU1 N 7/48 R4A. Does anyone have the SW module R3E02 & R4A?

[gaddag]

Hi! Prompt, please, what password on archive? A file upgrade2.4_pass.txt I can not download.

[sabila]

http://www.4shared.com/file/165583133/96278fa1/upgrade24.html

But 2.4 can be upgraded after u have 2.2

we can upgrade from 2.0 or 2.1
i had upgrade from this version
and working perfectly
thanks for the software :D

[sabila]

Hi! Prompt, please, what password on archive? A file upgrade2.4_pass.txt I can not download.

may u can post
and get more thanks for the other to increase your power level to download attachment

[filDim]

I have the MINI-LINK Service Software CD, a compilation of software and documentation for installation and service of MINI-LINK E, MINI-LINK TN, and MINI-LINK HC networks.

PM me if interested

[filDim]

Here are the links:

http://rapidshare.com/files/353478694/ML.part1.rar
http://rapidshare.com/files/353479430/ML.part2.rar
http://rapidshare.com/files/353445428/ML.part3.rar
http://rapidshare.com/files/353445433/ML.part4.rar

PM me for pwd after you add to my reputation and thanks, adding your username to reputation approval

[Cost_Reducer]

Hi ,

QUOTE=filDim;69492]I have the MINI-LINK Service Software CD, a compilation of software and documentation for installation and service of MINI-LINK E, MINI-LINK TN, and MINI-LINK HC networks.

PM me if interested[/QUOTE]

what version of ML-Craft for access the ML-TN nodes is included in this compilation? Is this 2.4 or 2.5 the latest Craft Version?

Regards

[gaddag]

Hi. Version 2.4 - last MiniLink Craft version.

[sabila]

Here are the links:

http://rapidshare.com/files/353478694/ML.part1.rar
http://rapidshare.com/files/353479430/ML.part2.rar
http://rapidshare.com/files/353445428/ML.part3.rar
http://rapidshare.com/files/353445433/ML.part4.rar

PM me for pwd after you add to my reputation and thanks, adding your username to reputation approval
hello fildim
can u explain what the latest software do you have for each minilink(MLE,TN,HCAP)

[Cost_Reducer]

hello fildim
can u explain what the latest software do you have for each minilink(MLE,TN,HCAP)

The last O&M Software for ML-TN is ML-Craft 2.5. This sw you need for baseline 4.3
O&M software 2.4 you need for baseline 4.2FP.

The last MiniLink E Manager is version 6.8.

I hope, this was helpful

Regards,

[headpointer]

thank you very much
>>>

[peep]

hi im new llalalalalalala

[MARKD]

Thanks a stack downloaded the mini link software could I please have the PW
Thanking u in advance

[sabila]

The last O&M Software for ML-TN is ML-Craft 2.5. This sw you need for baseline 4.3
O&M software 2.4 you need for baseline 4.2FP.

The last MiniLink E Manager is version 6.8.

I hope, this was helpful

Regards,

may u can upload that software

many thanks

[ofca]

@filDim - Could you post the release version number for MMU 2 D module for Traffic Node? I think the file should be called CXP9011133_4*
@cost_reducer - do you have ML Craft 2.5 and newest soft laying about somewhere?

Great posts, reped you both :)

[hinobd]

please give me password and thanks in advance.

[ofca]

Be advised, that contents of this disc are over 3 years old, and on top of that, there really isn't much on it to start with. Waste of time and bandwidth IMO.

For those in need, you can grab Minilink Craft 2.4 here:
http://rapidshare.com/files/359873868/mlcraft_2_4_install.exe.html

Still, I'm looking for Craft 2.5 and newest firmware set for Minilink Traffic Node - so if someone has it, please post! ;)

[wisammeesh]

thank u aloot

[headpointer]

Thank you very

[wolverinee]

thankssssss

[itsartur]

Hi,

Attached is the download link for E******* Minilink Operation & Maintenance software (Mini Link Craft 1.1)..

Password for zip file is "gsm"

Don't forget to say thank for those who find software good.

this software is very hard to find.
big thanks

[itsartur]

very good post.

thanks

[itsartur]

hi, great post.
what is the password for the links rapidshare that you post?
thanks

[itsartur]

why people put password and ask to send a Private Message to give password if new member can't send Private messages??

[itsartur]

someone give me the pw to mini link.rar

[itsartur]

Here are the links:

http://rapidshare.com/files/353478694/ML.part1.rar
http://rapidshare.com/files/353479430/ML.part2.rar
http://rapidshare.com/files/353445428/ML.part3.rar
http://rapidshare.com/files/353445433/ML.part4.rar

PM me for pwd after you add to my reputation and thanks, adding your username to reputation approval


HI i'm a new member so i can not send PM
coud you sent me PM with the PW
Thanks

[itsartur]

good post
thankx

[itsartur]

Be advised, that contents of this disc are over 3 years old, and on top of that, there really isn't much on it to start with. Waste of time and bandwidth IMO.

For those in need, you can grab Minilink Craft 2.4 here:
http://rapidshare.com/files/359873868/mlcraft_2_4_install.exe.html

Still, I'm looking for Craft 2.5 and newest firmware set for Minilink Traffic Node - so if someone has it, please post! ;)

which release do you need?
i can send you the ones you need

[bassem_16]

@itsartur

Do you have the new MLCT 2.5 ?

[itsartur]

@basem_16

no, sorry.

[ofca]

I need RAU2 X (CXP 901 2878) Release R1E if you have it somewhere.

[itsartur]

I need RAU2 X (CXP 901 2878) Release R1E if you have it somewhere.

http://www.megaupload.com/?d=0BNHKGLU

[ofca]

Now that was quick, useful and unexpected :) - thank you very much!

[ofca]

Thanks, it worked flawlessly and upgraded the RAUs. Could you perhaps post the whole Baseline R13A13 (CXP9010021_1) or at least MMU2D (CXP9011133/4) firmware R5A16 or newer?

[Cost_Reducer]

Ho Ofca,

R5A16 is from R4.2FP. I can upload this today....
btw...someone can upload ml-craft 2.5 and R4.3?

regards,

[Cost_Reducer]

Hi,

R5A16 (http://www.4shared.com/file/245193527/5201823b/CXP9011133_4_R5A16.html) is here !

[itsartur]

any time @ofca.

[ofca]

After upgrading both MMU and RAU, even without using 56MHz channels, I couldn't transmit any data over radio link. WAN interface reported 'lower layer down' and that's that. After downgrading MMU back to old release, everything went back green. Incompatible releases somewhere else?

Cost_Reducer, maybe you could post whole R4.2? :)

I'd also love to get MLCT2.5 and R4.3 :>

[Cost_Reducer]

hi ofca,

certainly i can share it here...this weekend?
Yes, it`s mandatory to use the same baseline / module software on both terminals. All modules must have the same baseline like the NPU!
Try this...i know that E\\\ have big problems with the co-operations between MLTN hardware and the different software revisions.

Regards

[ofca]

Glad to hear it; thought something was unexpectedly wrong. In that case it would seem, that I need two last things:

CXCR102051_1 and CXP9012516_2

Thanks for all your help...Again :)

[Cost_Reducer]

here (http://www.4shared.com/file/246026501/33ee4d97/SW_online.html)are both software versions

don`t forget to add reputation for me:D:D

[rainbow]

thanx fo cost reducer..
ur the best
its very hard to find this software...

many thanx 4 u, sorry i can't give reputation ( newbie mode :ON )

[ofca]

I already did and it said I can't give you any more now :(

[Cost_Reducer]

...it`s right, it is very difficult to get software for E******* products.
So this forum is the best place to share it with other members.


Regards,

CR

[ofca]

Aye, this forum is excellent. Glad I found it. And I'm glad you guys found it cost_reducer, and itsartur :)

[ofca]

Fighting continues...
@Cost_Reducer: Could you check what release you have for MMU for R4.2?
It's CXP9011133_4.

Also, do you use some kind of MSN, Jabber or smth? I would be able to stop the pointless forum trashing :>

[ofca]

OK, disregard. It was just me being stupid. Note to self: DCN Only = Bad. ;)

[Cost_Reducer]

OK, disregard. It was just me being stupid. Note to self: DCN Only = Bad. ;)

Hy ofca,

how do you mean, "DCN Only = Bad"
Do you have configured the MMU at "DCN only" ?

If i have the time tommorow evening, i will share product description of release 4.3.1 with you :D

[ofca]

Yes, I had the 'DCN Only' option enabled, not exactly knowing it's function. After short RTFM session I was much smarter, and disabling it made the problem go away. Well, error description could be a bit more descriptive :) - funny thing to note is: it was a problem only on newer firmware release - old MMU firmware worked fine anyway.

About product description: please do, at least I'll have something to look forward to :)

[Feriko]

Hello everyone,

I just want to make a question about this software...

What advantages does it have above the "traditional" web connection?

Thanks!

[byja]

After short RTFM session I was much smarter, and disabling it made the problem go away.

Swapping E/// equipment makes even more problems go away... :)

[ofca]

What kind of problems? All problems so far came from lack of my experience/knowledge - should I expect something? Please share your experiences with E///.

[Feriko]

As far as I know E// products are the best for me to handle. I've worked with minilink-C (very few wrorking now), minilink-E and now TN. These last ones are a bit problematic with some disconfiguration issues when changing parts. It's just having to backup all config and cross connections before touching anything...

Well now vodafone are putting some huawei RTN's in the network her in spain. Let's see...

[ofca]

my first impression is - it's very hard to cut yourself off while working on a live link. I did some daring things last few days and didn't manage to do anything I would permanently regret. Still, I'm fresh to TN, and don't have much experience with other products, so I would very much like to hear what others have to say on the topic.

[Cost_Reducer]

Hi,


As far as I know E// products are the best for me to handle. I've worked with minilink-C (very few wrorking now), minilink-E and now TN. These last ones are a bit problematic with some disconfiguration issues when changing parts. It's just having to backup all config and cross connections before touching anything...

Well now vodafone are putting some huawei RTN's in the network her in spain. Let's see...

ML-C & E are products for newbies, this equipment is easy to use & easy to understand. But the TN is very difficult, many software releases and hardware releases makes your live hard. Don`t forget this many bugs which are included in TN :rolleyes:
btw...huawei is the global winner of the vodafone rfq...we will see what happend with the good vodafone network quality :D


my first impression is - it's very hard to cut yourself off while working on a live link. I did some daring things last few days and didn't manage to do anything I would permanently regret. Still, I'm fresh to TN, and don't have much experience with other products, so I would very much like to hear what others have to say on the topic.

yu are new to TN and have not experience with other vendors...please tell me, wat kind of transmission you need, e.g pdh , sdh or ethernet?
Maybe then we can discuss about any vendors, like NERA,E*******,Ceragon,Huawei,Stratex...and so on.

P.S. What SW-Release do you use in ML-TN @ ofca? I observed, that 4.2FP have any problems in configuration with ethernet traffic over pdh if you use units like ETU3 and LTU12.


Regards,

CR

[ofca]

I'm mainly using TNs for ethernet transmission - with ethernet switch, however I'm also transporting E1 interfaces over wireless. BTW. Do you have R4.3.1 release notes yet? :)
As to the SW release, I think it's R4.2 - how can I reliably verify this?

[theharmonick]

I'm mainly using TNs for ethernet transmission - with ethernet switch, however I'm also transporting E1 interfaces over wireless. BTW. Do you have R4.3.1 release notes yet? :)
As to the SW release, I think it's R4.2 - how can I reliably verify this?

TN is the way to go for Ethernet transmission. I also used switches and ETH modules on the previous E******* products and transmitted Ethernet over E1, but it's not efficient...

[Cost_Reducer]

TN is the way to go for Ethernet transmission. I also used switches and ETH modules on the previous E******* products and transmitted Ethernet over E1, but it's not efficient...

In my opinion is TN not the way to go for Ethernet traffic. Dor Ethernet transmission i use the IP10 from Ceragon. IP10 have a nodal function and less of software releases / license keys :D
The TN i use for PDH transmission, but for SDH i use 1500R from Ceragon because Ceragon have a HighPower RFU for lower frequencies which support XPIC in 6,8Ghz / 40Mhz channel spacing. TN doesn`t support XPIC in 40mhz channels. Only in 128 QAM / 28 mhz channels.

If you want to verify the current software baseline you can look under software upgrade the current NPU baseline package and under "View modules" you can see the current modul software. Or you save a report in *.htm file and open it with web browser. Then you can see the current config and sw revision.
To compare the running sw with a SBL please download this (http://www.4shared.com/file/250529751/eac9d9fd/ML-TN_43_ETSI_Compatibility.html) document.

If you have any questions, pls ask !

[byja]

Speaking of ethernet transmission over mw radio, does anyone know how many traffic queues does TN have for QoS?
Most of the vendors have four traffic queues for 8 classes of service with fair or strict queueing, but I recently saw a request for eight. And I haven't seen any radio that supports it.

[ofca]

Thanks for the file. It seems that thanks to you and itsartur, I'm running at 4.2FP now. :)

[ofca]

@byja: Number of Traffic Class Queues - 8, it's in configuration of ethernet switch, and there are terms such as "Queues - Configure Packet Aging". Is this what you want?

[prle]

Speaking of ethernet transmission over mw radio, does anyone know how many traffic queues does TN have for QoS?
Most of the vendors have four traffic queues for 8 classes of service with fair or strict queueing, but I recently saw a request for eight. And I haven't seen any radio that supports it.

@byja

this is quotation from latest product description:

"All site LAN/WAN Ethernet ports can be configured with 1-8 traffic classes,
where 8 traffic classes are default.
The CoS priority information is used to map the Ethernet frames into the
1-8 traffic classes (TCs). The mapping can be done according to either
IEEE802.1D-2004, IEEE802.1Q-2005 or custom. Frames with no CoS
information is mapped to the default traffic class (TC0).
There are individual queues for each CoS. The Ethernet frames in the egress
queues are either scheduled according to a strict priority scheme or according to Weighted Fair Queuing (WFQ).
See Section 3.7.5.7 on page 47 for more information on strict priority, and Section 3.7.5.8 on page 47 for information on WFQ."

[Cost_Reducer]

Do you have R4.3.1 release notes yet? :)


here (http://www.4shared.com/file/252215531/38fb4eec/R43_-_Release_Note.html) you must look and download :p

[itsartur]

...hi everybody

can someone tell me if the version 2.5 of minilink is already available.

thanks.

[Cost_Reducer]

...hi everybody

can someone tell me if the version 2.5 of minilink is already available.

thanks.

yes take a look into this forum and you can download it but please note that 2.5 is old, 2.7 is up to date

[itsartur]

hi Cost,

i look up the forum and didn't find nothing about minilink TN 2.7

[Cost_Reducer]

hi Cost,

i look up the forum and didn't find nothing about minilink TN 2.7

you can`t find the 2.7 here but you can find the Craft terminal 2.5 here...posted by me :p

[bassem_16]

Has anyone faced any strange behaviour in software release 4.3.1 ?
Any problems that did occur, I know for instance that ML CT 2.5 is a bit slow when dealing with it so 2.7 is much more faster.

But I'm talking about any serious problems or unexplained behaviours
Thank you

[Cost_Reducer]

Has anyone faced any strange behaviour in software release 4.3.1 ?
Any problems that did occur, I know for instance that ML CT is a bit slow when dealing with it so 2.7 is much more faster.

But I'm talking about any serious problems or unexplained behaviours
Thank you

Sir,

i can say for me that i haven`t any behaviours at the moment with this software package because i didn`t test it very deep. This SW baseline was written to fix a bug with the power supply into AMM6.

And yes, you are right, ML Craft 2.5 is not the fastest LCT :p

[bassem_16]

Thanks cost reducer

I was thinking more about BER, or Tx off from links , unusual behaviour
I've seen it and was thinking its related to this SW but maybe not after all

[Cost_Reducer]

Thanks cost reducer

I was thinking more about BER, or Tx off from links , unusual behaviour
I've seen it and was thinking its related to this SW but maybe not after all

Bassem,

do you mean the internal BER-Test? You can test with teh internal BER from one site to remote site against a internal MMU loop.
What is with TX off ? If the TX off at far end you have the possibility to switch it On from near site. This works only if your links is established.
I have found a bug into this SW - Release...I established a link and have the management over the 2x64kbit channels to remote site but this management connection goes up and down...:eek: strange behavior


Cheers !

[bassem_16]

I'm talking about strange behaviours like you mentioned with 2x64kbit channels

What I meant by Tx off, that after installing this SW in one of the link, the Transmitter went off by itself !!! (we did make it on again, but why did it happen ?? )

[xnam]

In my opinion is TN not the way to go for Ethernet traffic. Dor Ethernet transmission i use the IP10 from Ceragon. IP10 have a nodal function and less of software releases / license keys :D
The TN i use for PDH transmission, but for SDH i use 1500R from Ceragon because Ceragon have a HighPower RFU for lower frequencies which support XPIC in 6,8Ghz / 40Mhz channel spacing. TN doesn`t support XPIC in 40mhz channels. Only in 128 QAM / 28 mhz channels.

If you want to verify the current software baseline you can look under software upgrade the current NPU baseline package and under "View modules" you can see the current modul software. Or you save a report in *.htm file and open it with web browser. Then you can see the current config and sw revision.
To compare the running sw with a SBL please download this (http://www.4shared.com/file/250529751/eac9d9fd/ML-TN_43_ETSI_Compatibility.html) document.

If you have any questions, pls ask !

Hi Cost_Reducer, please send me "MINI-LINK Radio Unit Compatibility" to vinhbinh2tg@yahoo.com.vn
I have AMM2p with RAU2 15 (SW R1E). After system upgrade SBL R11F18, warm restart, NE alarm "SoftwareEnvironmentProblem", "Load Module not Part of Baseline". Please help me for these alarms. Thanks,

[Cost_Reducer]

Hi XNAM,

please give me more informations about your placement of the plug-in units.
What kind of plug-in units are insert into AMM2p? Which kind of NPU?


Regards,

CR

[xnam]

Hi XNAM,

please give me more informations about your placement of the plug-in units.
What kind of plug-in units are insert into AMM2p? Which kind of NPU?


Regards,

CR

Hi Cost_Reducer,

NPU2, MMU2 B are insert into AMM2p.
Please help me.
BR,

[Cost_Reducer]

Hi Cost_Reducer, please send me "MINI-LINK Radio Unit Compatibility" to vinhbinh2tg@yahoo.com.vn
I have AMM2p with RAU2 15 (SW R1E). After system upgrade SBL R11F18, warm restart, NE alarm "SoftwareEnvironmentProblem", "Load Module not Part of Baseline". Please help me for these alarms. Thanks,


Hi Xnam,

now i have a little bit time for your issue. R11F18 is baseline version 3.3.5. Please make sure that NPU2 SW habe SW version R10F18 and the MMU2 must have SW state R3D06.
No more units are insert into AMM? Only a 4x2Mbps link?
What is your modulation scheme? QPSK or QAM? Please note that MMU2B can use only in QPSK mode. Capacities over 50Mbps are not applicable for MMU2b.

regards,

CR