PDA

View Full Version : Question Cell traffic offloading (balance)



telwind
2010-11-11, 01:33 PM
Dear all members,

What's the technical solutions to offload the traffic between cells in GSM? We put new site in service to add the capacity for resolving the congestion but the not much help. im thinking about the physical tuning like antenna direction pointing, downtilting, should any otherway like reduce power, direct retry,...

how to sort out this issue????

leelio
2010-11-11, 04:02 PM
To balance traffic to my understanding has to follow proper
1. new site planning- it should be close to the traffic,center to source of congestion.
2. rf configuration- tilt,azimuth has to reflect the reality, you can use coverage prediction tools(asset,etc) to set at your satisfaction.
3. on activation of a site- site integration(drive test) has to follow,do HO to neighbor site went fine? does site footprint meet your expectations? mostly ,neighbor sites need to be downtilted after coming of new sites;this had to be done when running coverage prediction for the site.
4. after all of above are OK, then you can start checking parameter setting (parameter optimisation).

mulham_kh
2010-11-11, 05:09 PM
Dear all members,

What's the technical solutions to offload the traffic between cells in GSM? We put new site in service to add the capacity for resolving the congestion but the not much help. im thinking about the physical tuning like antenna direction pointing, downtilting, should any otherway like reduce power, direct retry,...

how to sort out this issue????

Dear
After the Physical soluations you can also use the parameters like neagtive CRO which push the traffic to another cells in Idle mode or OffsetN , OffsetP which balancing the traffic between the cell and its neighbors in dedicated mode.
Regards
Molham Khoja

salamanda1969
2010-11-11, 06:33 PM
Dear all members,

What's the technical solutions to offload the traffic between cells in GSM? We put new site in service to add the capacity for resolving the congestion but the not much help. im thinking about the physical tuning like antenna direction pointing, downtilting, should any otherway like reduce power, direct retry,...

how to sort out this issue????

Assuming, this site is already built & on air, here are some options (descending effectiveness):
- add Half rate, G1800, add sectors
- adjacent cells physical retune: antenna tilt, azimuth
- push idle mode MS to other 'good' cells
- force dedicated MS to HO to other cells
- play with CRO, Rxlev Min Access (watch out for unhappy customers)
- etc

Hope this helps.

telwind
2010-11-11, 08:01 PM
thanks for all experts having great sharing

@ mulham and salamanda, CRO OffsetN, OffsetP are for specific vendor?

Anyway, thanks for your share again.

Jakkrit
2010-11-13, 03:37 AM
About locating parameters such as HO(dedicated mode) & CR(idle mode) are avialable in all main vendors, but it's differrent named (offset, margin, threshold, etc). However the concept and algorithm aren't different so much.

guruvai
2010-11-13, 07:29 AM
thanks for all experts having great sharing

@ mulham and salamanda, CRO OffsetN, OffsetP are for specific vendor?

Anyway, thanks for your share again.

CRO (Cell reselection Offset) is for E*******.
Lower value of CRO will favor the neighbouring cells on Idle mode reselection. whereas a higher (say -104 instead of the default -110) setting of ACCMIN (minimum received signal level in dBm at the MS) will make surrounding cells more favourable on idle mode reselection. So, play with these things. :)

Darko
2010-11-13, 10:50 PM
You can check traffic distribution for neighboring cells and if possible try adjusting Cell Load Sharing(CLS) feature parameters to offload traffic from congested cells (E*******).
This is useful only during busy hours.

Also you can adjust Multi Band Cell feature (MBC) parameters (if available) to transfer more traffic to other band (if you have enough resources available for the second band).

telwind
2010-11-14, 12:59 AM
You can check traffic distribution for neighboring cells and if possible try adjusting Cell Load Sharing(CLS) feature parameters to offload traffic from congested cells (E*******).
This is useful only during busy hours.

Also you can adjust Multi Band Cell feature (MBC) parameters (if available) to transfer more traffic to other band (if you have enough resources available for the second band).

Thanks all for very helpful sharing.

Anyone could share the documents about system feature like CRO, CLS, etc?

guruvai
2010-11-14, 01:25 AM
Thanks all for very helpful sharing.

Anyone could share the documents about system feature like CRO, CLS, etc?

You'll find all of the features in my post (http://www.finetopix.com/e*******/13176-gsm-radio-network-features-you-need-know.html). Find CRO in Idle mode behavior.

luganomu
2010-11-14, 02:13 AM
attached file can help!!

luganomu
2010-11-14, 02:30 AM
Can same one tell how to reduce/remove call setup failure due to expire of the call attemp time out/ setup time?

telwind
2010-11-15, 04:53 PM
You'll find all of the features in my post (http://www.finetopix.com/e*******/13176-gsm-radio-network-features-you-need-know.html). Find CRO in Idle mode behavior.

thanks again, very useful to me

luganomu
2010-11-18, 02:07 AM
The file need credit can you send it via email luganomu@yahoo.co.uk