Default Values fo events 6 3G (UE internal measurements)

[Samucka]

Hello,

I have been walking with some doubts about events 6 (UE internal measurements) in 3G.

Should They be allways active?in CS and/or PS sessions?

What values should events 6 have, in terms of time-to-trigger, thresholds, etc..?

Someone knows something about that?typical values for them... experiency and knowhow...

Thanks in advance,
Sam




ftp://ftp.ua.pt/incoming/Event6/Events6_DriveTest.jpg

ftp://ftp.ua.pt/incoming/Event6/Events6_Thresholds.jpg

[Samucka]

Hi,

can anybody help me?

These events 6 (UE internal measurements) are related with handover in 3G.
Can you check in your network how they configured?

Please let me know.

Thank you,
Sam

[eritelecom]

event6a : UE TX power higher than a max threshold (RNC controlled).
as far as I remember this threshold is about 10 dbm. give me time to check

eritelecom

[wolverine]

It is good to have these triggers as well, nothing to lose. They are especially useful if you have cells with high UL RSSI. I would suggest you use your vendors recommended settings first and then tweak as needed.

Usually triggers are around the 20-22dBm mark (considering most UEs are power class 3 i.e. max Tx power 24dBm)

[Samucka]

Hi,

Wolverine and Eritelecom thank you for your answers.


At this moment in network they are configured like it´s showed bellow.
For me, I think that these values are not the best.

"
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 24, TTT: 100 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 22, TTT: 100 (ms)
"

Can you suggest a new configuration or values that you have in your live networks for these parameters?


Thanks,

[senjamir]

Hi,

Wolverine and Eritelecom thank you for your answers.


At this moment in network they are configured like it´s showed bellow.
For me, I think that these values are not the best.

"
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 24, TTT: 100 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 22, TTT: 100 (ms)
"

Can you suggest a new configuration or values that you have in your live networks for these parameters?


Thanks,


Hi,

You can also set event 6 measurements as HO criteria. This will enable you to have a better quality of signal based on the power transmitted by the UE.

If the system is Nokia you may use the following configuration:
GsmUETxPwrThrAMR - -3dB
GsmUETxPwrThrCS - -3dB
GsmUETxPwrThrNrtPS - -1dB
GsmUETxPwrThrRtPS - -3dB
GsmUETxPwrTimeHyst - 320 ms

If the system is E******* you may use the following values:
ueTxPowerThresh6b - 18 dBm
timeTrigg6d - 320 ms
timeTrigg6b - 1280 ms

Hope this might help you.

Br,

Sen

[Samucka]

Hi,

You can also set event 6 measurements as HO criteria. This will enable you to have a better quality of signal based on the power transmitted by the UE.

If the system is Nokia you may use the following configuration:
GsmUETxPwrThrAMR - -3dB
GsmUETxPwrThrCS - -3dB
GsmUETxPwrThrNrtPS - -1dB
GsmUETxPwrThrRtPS - -3dB
GsmUETxPwrTimeHyst - 320 ms

If the system is E******* you may use the following values:
ueTxPowerThresh6b - 18 dBm
timeTrigg6d - 320 ms
timeTrigg6b - 1280 ms

Hope this might help you.

Br,

Sen


Hi senjamir,

and about e6a?

Someone knows about Huawei parametrization?


I have two events e6a and two events e6b (checked by Tems Investigation)
Is this related with UEs with diferent power class (21dBm or 24dBm)?


BR,
Sam

"
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 24, TTT: 100 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 22, TTT: 100 (ms)
"
source:Tems

[Samucka]

Hi senjamir,

and about e6a?

Someone knows about Huawei parametrization?


I have two events e6a and two events e6b (checked by Tems Investigation)
Is this related with UEs with diferent power class (21dBm or 24dBm)?


BR,
Sam

"
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 24, TTT: 100 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6a Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 23, TTT: 240 (ms)
e6b Measured Quantity: UE Transmitted Power, Transmitted Power Threshold: 22, TTT: 100 (ms)
"
source:Tems


Hi,

someone can help me?

BR,
Sam